Panasonic WH-SDC07C3E5 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 166

background image

84

14 Protection Control

14.1. Protection Control For All Operations

14.1.1.

Time Delay Safety Control

1. The compressor will not start for three minutes after stop of operation.

14.1.2.

30 Seconds Forced Operation

1. Once the compressor starts operation, it will not stop its operation for 30 seconds.
2. However, it can be stopped using control panel at indoor unit.

14.1.3.

Total Running Current Control

1. When the outdoor running current exceeds X value, the compressor frequency will decrease.
2. If the outdoor running current does not exceed X value, the compressor frequency will return to normal operating frequency.
3. If the outdoor running current continue to increase till exceed Y value, compressor will stop, and if this occurs 3 times within

20 minutes, system will stop operation and OFF/ON control panel LED will blink (F16 error occurs).

14.1.4.

IPM (Power transistor) Prevention Control

A. Overheating Prevention Control

1. When the IPM temperature rises to 95

°

C, compressor will stop immediately.

2. Compressor will restart delay 3 minutes when the IPM temperature decreases to 90

°

C.

If this condition repeats continuously 3 times within 30 minutes, system will stop operation and OFF/ON control panel LED will
blink (F22 error occurs).

B. DC Peak Current Control

1. When the current to IPM exceeds set value of 40.1 ± 5.0 A (UD07CE and UD09CE), 44.7 ± 5.0 A (UD12CE, UD14CE and

UD16CE), compressor will stop. Compressor will restart after three minutes.

2. If the set value exceeds again for more than 30 seconds after the compressor restarts, operation will restart after two minutes.
3. If the set value exceeds again for within 30 seconds after the compressor restarts, operation will restart after one minute. If

this condition repeats continuously for seven times, system will stop operation and OFF/ON control panel LED will blink (F23
error occurs).

14.1.5.

Compressor Overheating Prevention Control

• The compressor operating frequency is regulated in accordance to compressor tank temperature as shown in below figures.

When the compressor tank temperature exceeds 112

°

C, compressor will stop, and if this occurs 4 times within 30 minutes,

system will stop operation and OFF/ON control panel LED will blink (F20 error occurs).

07C

09C

12C

14C

16C

Operation Mode

X (A)

Y (A)

X (A)

Y (A)

X (A)

Y (A)

X (A)

Y (A)

X (A)

Y (A)

Heating

20.9

27.9

22.7

27.9

24.0

27.9

25.0

27.9

26.0

27.9

Cooling

13.8

27.9

14.6

27.9

16.0

27.9

19.7

27.9

22.6

27.9

«
...
82
83
84
85
86
...
»

Содержание WH-SDC07C3E5







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SDC07C3E5

Бренд: Wayne Страницы: 8

Бренд: Calpeda Страницы: 32

Бренд: Zehnder Rittling Страницы: 20

Бренд: Pro-Elec Страницы: 4

Бренд: salmson Страницы: 36

Ecosun 300 Basic

Бренд: Fenix Страницы: 16

Бренд: EBARA Страницы: 172

Бренд: Champion Страницы: 27

Бренд: Carrier Страницы: 16

Бренд: NewAir Страницы: 12

Бренд: SFA Страницы: 28

BIO-1500PCPremium Classic

Бренд: Bio Smart Technologies Страницы: 28

Бренд: Cooper & Hunter Страницы: 25

Бренд: Stairs Страницы: 2

Бренд: E-FLOR Страницы: 136

Бренд: K2 Pumps Страницы: 29

Бренд: TapFlo Страницы: 56

Бренд: Grundfos Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды