Panasonic Viera TC-P42X1 Скачать руководство пользователя страница 38

Страница: 38 / 71

Slide #38

5 Blinks Error Code (All Models)

Trouble Mode

5V SOS

Defective Board

P, C, A,SC, SS board or Panel

Disconnect the TV. Measure the resistance

between pin 1 of connector P35 on the P

board and ground (Chassis).

Yes

Proceed to more extensive troubleshooting

of the slides that follow.

Is there a

short to

ground?

Panel

Note:

Even though it

does not happen often,

the 5 blinks shutdown

can also be caused by

one of the C boards

Warning:

Disconnect AC Power prior to

making any disconnection or connection.

Does the power

supply

makes a “chirp”

noise at plug in?

Start Here

Yes

Is there a

short to

ground?

Replace

the SS board

Replace

the SC board

Disconnect the TV. Disconnect

P2 and P11 on the P board

Measure the resistance between

pin 1 of connector SS11 on the

SS board and ground (Chassis).

Yes

Is there a

short to

ground?

All other 2009 Models

TC-P42G10

TC-P46G10

TC-50G10

TC-P54G10

Measure the resistance between

pin 1 of connector SC2 on the SC

board and ground (Chassis).

Replace

the P board

Start Here

If the power LED continues to blink even after the TV is unplugged, press and hold the power
switch on the TV for a few seconds until the LED turns off.

Содержание Viera TC-P42X1








































































Результаты поиска

Содержание Viera TC-P42X1

Отзывы:

Похожие инструкции для Viera TC-P42X1

Бренды по названию

Популярные бренды

Panasonic Viera TC-P42X1, Исправленное руководство по устранению неисправностей

Результаты поиска

Содержание Viera TC-P42X1

Отзывы:

Похожие инструкции для Viera TC-P42X1

Бренды по названию

Популярные бренды