Panasonic VB-44210G Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-29

DP/DTMF Stations

(All Versions)

Description

The DBS allows both dial pulse and DTMF extension types.

Related Programming

• FF2 (Trunk): DTMF/Pulse Dialing for Trunks

Considerations

• DP to DTMF Signal Conversion allows DTMF extensions to use either

dial pulse or DTMF trunks.

DP to DTMF Signal Conversion

(All Versions)

Description

This feature allows an extension user to switch from DP to DTMF signaling
when using a DP trunk.

For instance, if a user dials into a voice mail system using a DP trunk, the user
can switch to DTMF signaling to communicate with the voice mail system.

DTMF tones can be sent either during the call or while the call is being
dialed.

Operation

To switch from dial pulse to DTMF dialing, press “*” or “#.”

Related Programming

• FF2 (Trunk): DTMF/Pulse Dialing for Trunks

Considerations

• DTMF dialing remains in effect for the duration of the call. Pulse dialing is

restored when the handset is replaced.

«
...
73
74
75
76
77
...
»

Содержание VB-44210G











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VB-44210G

Бренд: jablotron Страницы: 2

Бренд: AEI COMMUNICATIONS Страницы: 5

Бренд: Fender Страницы: 6

DECT2060-2 - DECT Cordless Phone

Бренд: Uniden Страницы: 56

Бренд: BT Страницы: 72

MT4-16 MovieTimeS

Бренд: SMART Страницы: 17

NANOpure DIamond D11931

Бренд: Barnstead|Thermolyne Страницы: 56

Бренд: Net2Phone Страницы: 20

Бренд: Radio Shack Страницы: 24

Бренд: Trevi Страницы: 24

DXI8560-2 - DXI Cordless Phone

Бренд: Uniden Страницы: 20

Бренд: Nortel Страницы: 8

Бренд: switel Страницы: 112

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 18

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды