7
English
CAUTION
Do not bring your hands, face or objects close to the
ventilation holes of the Display.
•
Heated air comes out from the ventilation holes at the
top of Display will be hot. Do not bring your hands or
face, or objects which cannot withstand heat, close to
this port, otherwise burns or deformation could result.
Do not place the display where it may be affected by
salt or corrosive gas.
•
Doing so may cause the display to fall due to
corrosion, and it may result in injury. Also, the unit
may malfunction.
When disconnecting the power supply cord, always
pull on the plug (socket outlet side) / the connector
(main unit side).
•
Pulling the cord may damage the cord, and it may
cause electric shock or fire due to short-circuit.
Be sure to disconnect all cables before moving the
Display.
•
If the Display is moved while some of the cables are
still connected, the cables may become damaged,
and fire or electric shock could result.
Disconnect the power supply plug from the wall
socket as a safety precaution before carrying out
any cleaning.
•
Electric shocks can result if this is not done.
Do not step on, or hang from the display or the
Pedestal.
•
They might tip over, or might be broken and it may
result in injury. Pay special attention to the children.
Do not reverse the polarity (+ and -) of the battery
when inserting.
•
Mishandling the battery may cause its explosion
or leakage, resulting in fire, injury or damage to
surrounding properties.
•
Insert the battery correctly as instructed. (see page
10)
Do not use batteries with the outer cover peeling
away or removed.
•
Mishandling the batteries may cause the batteries
to short circuit, resulting in fire, injury or damage to
surrounding properties.
Remove the batteries from the remote control
transmitter when not using for a long period of time.
•
The battery may leak, heat, ignite or burst, resulting in
fire or damage to surrounding properties.
Remove exhausted batteries from the remote control
immediately.
•
Leaving the batteries unattended in it may cause
battery leakage, heat or burst.
Do not burn or breakup batteries.
•
Batteries must not be exposed to excessive heat such
as sunshine, fire or the like.
Do not turn the Display upside down.
Do not position the unit with its display panel facing
upright.
Precautions for use
Cautions when installing
Do not set up the Display outdoors.
•
The Display is designed for indoor use.
Install this unit at a location which can support the
weight of the unit.
•
Dropping or falling of the unit may cause injury.
Do not install the unit near a high-voltage line or a
power source.
•
Installing the unit near a high-voltage line or a power
source may receive interference.
Install the unit away from heat appliances.
•
Failure to do so may cause deformation of the cabinet
or malfunction.
Environmental temperature to use this unit
•
When using the unit where it is below 1 400 m
(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to
104 °F)
•
When using the unit at high altitudes (1 400 m
(4 593 ft) and higher and below 2 800 m (9 186 ft)
above sea level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
•
Failure to do so may shorten the life of the internal
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Transport only in upright position!
•
Transporting the unit with its liquid crystal panel
facing upright or downward may cause damage to the
internal circuitry.
Do not grab the liquid crystal panel.
•
Do not forcibly press the liquid crystal panel, or push
it with a pointed object. Applying a strong force to
the liquid crystal panel will cause unevenness of the
screen display, resulting in malfunction.
Do not install the product to a place where the
product is exposed to direct sunlight.
•
If the unit is exposed to direct sunlight even indoors,
the temperature rise of the liquid crystal panel may
cause malfunction.
In the case of storage, store the unit in a dry room.
Required space for ventilation
•
When installing the unit in a case or chassis, provide
a cooling fan or ventilation hole to ensure appropriate
ventilation so that the temperatures surrounding the
unit including the front surface of the liquid crystal
panel (temperature of inside the case or chassis)
can be maintained within the range of the operating
temperature of the unit.
