background image

RQT5717

26

Reference

Specifications

SPEAKER SECTION

Type

2 way speaker system

Speaker(s)

Superwoofer

10 cm (3

15

/

16

˝) cone type

Full range

8 cm (3

1

/

8

˝) cone type

Impedance

High (6

Ω)

, Low (6

)

Input power

High 10 W (Music)

Low 35 W (Music)

Output sound pressure level

86 dB/W (1.0 m)

Cross over frequency

110 Hz

Frequency range

55 Hz–25 kHz (–16 dB)

75 Hz – 22 kHz (–10 dB)

Dimensions (WxHxD)

140 x 240 x 213 mm

(5

1

/

2

˝ x 9

7

/

16

˝ x 8

3

/

8

˝)

Mass

2.3 kg (5.1 lb)

GENERAL

Power supply

AC 120 V, 60 Hz

Power consumption

64 W

Standby

0.6 W

Dimensions (WxHxD)

180 x 241 x 318 mm

(7 

3

/

32

˝x 9 

1

/

2

˝ x 12 

1

/

2

˝)

Mass

4.6 kg (10.1 lb)

Notes:
1. Specifications are subject to change without notice.

Mass and dimensions are approximate.

2. Total harmonic distortion is measured by the digital spectrum

analyzer.

Maintenance

CD SECTION

Sampling frequency

44.1 kHz

Decoding

16 bit linear

Beam source/wave length

Semiconductor laser/780 nm

Number of channels

Stereo

Wow and flutter

Below measurable limit

Digital filter

8 fs

D/A converter

MASH (1 bit DAC)

For a cleaner crisper sound

Clean the heads regularly to assure good quality playback and
recording.
Use a cleaning tape (not included).

AMPLIFIER SECTION

Power output

1% Total harmonic distortion

30 Hz–160 Hz, both channels driven

 (Low channel) 9 W per channel (6

)

160 Hz–20 kHz, both channels driven

(High channel) 4 W per channel (6

)

Total Bi-Amp power

13 W per channel

Input sensitivity

AUX

250 mV

Input impedance

AUX

47 k

Output impedance

Headphone

16-32

FM TUNER SECTION

Frequency range

87.9–107.9 MHz (200 kHz steps)
87.5–108.0 MHz (100 kHz steps)

Sensitivity

1.8 µV (IHF)

S/N 26 dB

1.5 µV

Antenna terminal(s)

75

 (unbalanced)

AM TUNER SECTION

Frequency range

AM

520 – 1710 kHz (10 kHz steps)

Sensitivity

AM
S/N 20 dB (at 999 kHz)

500 µV/m

CASSETTE DECK SECTION

Track system

4 track, 2 channel

Heads

Record/playback

Solid permalloy head

Erasure

Double gap ferrite head

Motor

DC servo motor

Recording system

AC bias 100 kHz

Erasing system

AC erase 100 kHz

Tape speed

4.8 cm/s

Frequency response
(+3 to -6 dB at DECK OUT)

NORMAL (TYPE I)

50 Hz – 13 kHz

HIGH (TYPE II)

50 Hz – 13 kHz

S/N

52 dB (A weighted)

Wow and flutter

0.18% (WRMS)

Fast forward and rewind times

Approx. 120 seconds with

C-60 cassette tape

If the surfaces are dirty

To clean this unit, wipe with a soft, dry cloth.
If the surface are extremely dirty, use a soft cloth dipped in a soap-
and-water solution or a weak detergent solution.

• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically treated cloth, read the instructions that

came with the cloth carefully.

Product Service

Product information

For product service, product information or assistance with product
operation, refer to the servicenter directory.

In the U.S.A., contact the Panasonic Customer Call Center at
1-800-211-7262, or e-mail [email protected],
or web site (http://www.panasonic.com).
In Canada, contact Panasonic Canada Inc. Customer Care
Centre at 905-624-5505, web site (www.panasonic.ca), or an
authorized Servicentre closest to you.

Do not attempt to remove the cover(s) or repair the unit yourself.
Refer servicing to qualified personnel only.

e23-28

3/25/05, 4:38 AM

26

Содержание SCPM25 - CD STEREO SYSTEM





























Отзывы: