10 Disassembly and Assembly of Main Component
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1.-This section describes procedures for checking the operation of the major printed circuit boards and replacing the
main components.
2.-For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3.-Select items from the following index when checks or replacement are required.
4.-Refer to the Parts No. on the page of “Main component Replacement Procedures”, if necessary.
10.1 Disassembly flow chart
The following chart is the procedure for disassembling the
casing and inside parts for internal inspection when carrying
out the servicing.
To assemble the unit, reverse the steps shown in the chart as
below.
10.2 Gear for servicing (jig) Information
1.-This unit has a gear which is used for checking items
(Open/Close of disc tray, up/down operation of traverse unit
by manually) when servicing.
2.-For preparation of gear (for servicing), perform the
procedures as follows.
3.-In case of re-servicing the same set, the “gear for
servicing” may has been taken off because it has been used.
The “gear for servicing” must be stored.
·
Remove the gear provided with mechanism cover as
shown below.
9
Содержание SC-TM23
