RQ
TX00
14
33
T
roub
le
sh
oo
tin
g g
ui
de
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not
solve the problem, refer to “Customer Services Directory” on page 38 if you reside in the U.S.A., or refer to “Product information” on page 37 if you
reside in Canada.
(Continued on next page)
Power
No power.
≥
Insert the AC power supply cord securely.
8
The unit is automatically switched
to standby mode.
≥
The Sleep timer was working and had reached the set time limit.
10
Unit displays
The display is dark.
≥
Select “Bright” in “FL Dimmer” in the “Others” menu.
25
“NO PLAY”
≥
You inserted a disc the unit cannot play; insert one it can.
≥
You inserted a blank disc.
≥
You inserted a disc that has not been finalized.
12
—
—
“NO DISC”
≥
You have not inserted a disc; insert one.
≥
You have not inserted the disc correctly; insert it correctly.
—
14
“F61”
≥
Check and correct the speaker cable connections.
If this does not fix the problem, consult the dealer.
5
“F76”
≥
There is a power supply problem. Consult the dealer.
—
“DVD U11”
≥
Disc may be dirty. Wipe it clean.
13
“ERROR”
≥
Incorrect operation performed. Read the instructions and try again.
—
“DVD H
∑∑
”
“DVD F
∑∑∑
”
∑
stands for a number.
≥
Trouble may have occurred. The numbers following “H” and “F” depend on the status of the unit.
Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC power supply
cord, and then reconnect it.
≥
If the service numbers fail to clear, note the service number and contact a qualified service person.
—
—
“D.MIX” is flashing.
[DVD-A]
≥
Down-mixing is the process of remixing the 5.1 channel sound found on some discs into two
channels. The disc contains single-channel or 5.1 channel signals which may not be reproduced
authentically.
—
“U70
∑
”
∑
stands for a number.
The actual number following “U70”
will depend on the state of the main
unit.
≥
The HDMI connection acts unusually.
– The connected equipment is not HDMI-compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is too long.
– The HDMI cable is damaged.
—
—
—
—
“XM RADIO”
≥
It takes a short time for the XM radio to power up after turning on the main unit, during which time
“XM RADIO” is displayed (only when the selected source is XM).
Wait a few seconds for this process to complete.
—
“XM ERROR”
≥
There may be an error in the XM radio module. Turn the main unit off, and then back on.
≥
The XM antenna may be defective. Consult the dealer of the XM antenna.
—
—
“REMOTE 1” or “REMOTE 2”
≥
Match the modes on the main unit and remote control. Depending on the number being displayed (“1”
or “2”), press and hold [ENTER] and the corresponding numbered button ([1] or [2]) for at least 2 seconds.
10
General operation
No response when any buttons
are pressed.
≥
This unit cannot play discs other than the ones listed in these operating instructions.
≥
The unit may not be operating properly due to lightning, static electricity or some other external
factor. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC power
supply cord, and then reconnect it.
≥
Condensation has formed. Wait 1 to 2 hours for it to evaporate.
12
—
—
No response when remote control
buttons are pressed.
≥
Check that the batteries are installed correctly.
≥
The batteries are depleted. Replace them with new ones.
≥
Aim the remote control at the remote control signal sensor and operate.
8
8
11
Other products respond to the
remote control.
≥
Change the remote control operating mode.
10
No picture or sound.
≥
Check the video or speaker connection.
≥
Check the power or input setting of the connected equipment and the main unit.
≥
Check that the disc has something recorded on it.
5, 6, 7
—
—
You have forgotten your ratings
password.
Reset all the settings to Factory
Preset.
≥
While stopped and “DVD/CD” is the source, press and hold [
∫
] (Stop) on the main unit and [
S
10]
on the remote control until “Initialized” disappears from the television. Turn the unit off and on
again.
All settings will return to the default values.
—
The EZ Sync “HDAVI Control”
function does not respond.
≥
Depending on the condition of the home theater system or the connected equipment, it may be
necessary to repeat the same operation so that the function can work correctly.
26
Cannot operate the television.
≥
Check the remote control code for the television manufacturer.
10
0014En_p26-40.fm Page 33 Friday, June 8, 2007 12:19 PM
