Panasonic SA-HT833VP, Руководство по обслуживанию

Страница: 19 / 158

Display Type of error Description
CD F 28 DISC loading error During the horizontal motion toward to PLAY position, if there is no change when it exceeds the fail
safe timer or if counter direction does not enter into state of target, will be keep it memory mode.
Initialization is done when the next mecha mode starts.
Only when backup data is cleared of this error no. when it compels clearly or power supply start-up.
CD F 29 DISC unloading error During the horizontal motion toward opposite direction to PLAY position, if there is no change when it
exceeds the fail safe timer or if counter direction does not enter into state of target, will be keep it
memory mode. Initialization is done when the next mecha mode starts.
Only when backup data is cleared of this error no. when it compels clearly or power supply start-up.
CD F 27 DOWN SW error Memory when bottom switch is not changed even if it exceeds it to time of fail safe timer when going
up and down operates toward bottom position. When mechanism begins to operate next time,
initialization is done.
Only when backup data is cleared clearly of this error No. when it compels clearly or power supply
start-up.
CD F 22 Mechanism is loading
motor/abnormal
Memory at the initialization of mechanism due to abnormality of the loading motor or the mechanism
when entering the state usually cannot. When mechanism begins to operate next time, initialization is
done.
Only when backup data is cleared clearly of this error No. when it compels clearly or power supply
start-up.
F 03 Traverse servo error
F 04 Tracking servo error
F 05 Seek error
F 06 Power supply error Power cannot be turned off due to communication error between panel computer and system
computer.
F 61 Power supply error Abnormal output or power supply abnormal circuit of Power Amp.
10.2.2. Error Code Display
1. Set to DVD/CD mode (Ensure no disc is loaded)
2. While pressing and holding down the [STOP] on main unit and press [0] on remote control in order to display the latest error
code. (Automatically cancelled after five seconds.)
Note: No error code will show if there is no problem with unit. Refer below for error code display.
(Error Code Display)
Section Code Meaning Note
Disc code F103 Illegal Highlight Position Possibility of illegal disc when highlight is displayed
Decoder related F220 Y level adjustment failure Brightness signal level adjustment cannot be properly
operated
F221 C level adjustment failure Color signal level adjustment cannot be properly
operated
II C error F4FF Compulsory initialization failure (time out)
DSC related F500 DSC error DSC stops due to servo failure. (Startup, focus failure,
etc.)
F501 DSC not ready Communication failure between DSC and system
computer(No communication because DSC does not
move)
F502 DSC time out failure See F500.
F503 DSC communication failure Communication failure (Result failure occurs after
communication command is transmitted.)
F504 Data slice offset adjustment failure Not in use. (FEP error)
F505 DSC Attention Error See F500.
F506 Invalid media Disc is placed upside down; TOC is unreadable or
invalid disc is inserted.
ODC related F600 Control information unattainable due to demodulation
error Operation stops because navigation data cannot be
obtained due to demodulation system failure.
F601 Unknown sector ID requested Operation stops because access of illegal ID data is
requested.
F602 LEAD-IN unattainable due to demodulation error Unable to read LEAD IN data
F603 KEYDET unattainable due to demodulation error Unable to obtain CSS data
F610 ODC failure No permission of command issue
F611 6626 QCODE don´t read ERROR Unable to obtain seek address at CD system
F612 No CRC OK during a certain time of duration Unable to obtain ID data at DVD system
F630 No response to KEY DET makeshift (Internal use)
F631 CPPM KEY DET unavailable to FILE end terminal CPPM fail system cannot be read due to scratch.
F632 CPPM KEY DET unavailable Revoke or altered.
19
SA-HT833VP