manualshive.com logo in svg

Panasonic PT56DLX75 - 56" DLP TV, Руководство пользователя, Страница: 73 / 107

Поделиться
Скачать
Panasonic PT56DLX75 - 56

-41-

REMOVAL OF THE FRONT JACK C.B.A. (CIRCUIT BOARD FJ), THE CARD C.B.A., THE
REAR JACK C.B.A., THE POWER C.B.A. (CIRCUIT BOARD P), THE  MAIN C.B.A.
(CIRCUIT BOARD DG) AND THE BASE C.B.A. (CIRCUIT BOARD A) FROM THE TV UNIT

1. CAUTION:
Be sure to make a note of the CURRENT LAMP value (value A) in Service Mode (1/4):
LAMP OPERATION TIME is stored in EEPROM on the Main C.B.A. Therefore, before removing the Main C.B.A. or the TV Unit at
the user’s location, make a note of the CURRENT LAMP value (value A) in Service Mode (1/4).
Then, after installing the new Main C.B.A. or the TV Unit at the user’s location, set the CURRENT LAMP value to the original value
(value A) in Service Mode.
Otherwise, OSD and LED Lamp replacement indications will be displayed at the wrong time.

Note:
In case it is impossible to make a note of the CURRENT LAMP value because of a defective Main C.B.A., ask the customer
their daily average use and the approximate age of the current Lamp. Then, calculate the CURRENT LAMP value as follows
and make a note.

Daily average use

X

=

Approx. age

 CURRENT LAMP

 (hours)

 (days)

 (hours)

Replacement Note for Card C.B.A.:
These parts will be necessary when replacing. Set aside, keep, and re-use.
-

P9003 Connector Cable

3. 1) Remove the Front Jack Earth Plate by removing Screw (402).

2) Disconnect Connectors P3901, P3902, P3903.
3) Remove the Front Jack C.B.A. by removing the 2 Screws (421).
4) Remove the Front Jack Holder with the Card C.B.A. by removing Screw (402) then releasing the 2 Locking Tabs.
5) Remove the Card C.B.A. by removing the 2 Screws (421).

Fig. D4-2

2. Remove the TV Unit. Refer to Steps 1~3 in "REMOVAL OF THE TV UNIT FROM THE CABINET."

402

402

421

421

421

421

Front Jack C.B.A. (Circuit Board FJ)

Card C.B.A.

P9003

Connector 
Cable

Front Jack Holder

Locking Tabs

P3903

P3901

P3902

Clampers

Front Jack 
Earth Plate

Содержание PT56DLX75 - 56" DLP TV












































































































Отзывы:

Нет отзывов