manualshive.com logo in svg

Panasonic PT56DLX75 - 56" DLP TV, Руководство пользователя, Страница: 67 / 107

Поделиться
Скачать
Panasonic PT56DLX75 - 56

-35-

401

Optical Block Unit

*: The 5 Screws *(401) are for removing the Optical Block Unit

*

401

*

401

*

Guide Tabs (X4)

<Bottom View of Optical Block Unit>

1 2 3

3

401

*

2

401

*

1

Reassembly Note for Optical Block Unit: When installing, tighten the 3 Screws (401)               in order.

401

Sealing Cover

Clampers

Screw for 
GND 

Screw for GND

Clamper

Clamper

Clamper

Clamper

B2
(From Base
C.B.A.)

PL4 
(From Base 
C.B.A.)

PL5 
(From Main 
C.B.A.)

PL1 (20-pin Cable)
(From Main C.B.A.)

Fan 2 Connector

Thermostat/Cover Switch Connector

B1
(From Power
C.B.A.)

Slide and 
lift up the 
Optical Block Unit

Sealing 
Cover

401

401

3. 1) Remove the 2 Screws for GND to disconnect the 20-pin Cable.

2) Disconnect Connectors B1, B2, PL1 (20-pin Cable), PL4, PL5, the Thermostat/Cover Switch Connector and the Fan 2

Connector then releasing the clampers.

Note: Take extreme care not to damage the 20-pin Cable when disconnecting.

4. 1) Remove the 2 Screws (401), and remove the Sealing Cover.

2) Remove the 3 Screws (401), and then slide and lift up the Optical Block Unit by releasing the 4 Guide Tabs.

Fig. D1-3

Содержание PT56DLX75 - 56" DLP TV












































































































Отзывы:

Нет отзывов