Panasonic PT-VW330U Скачать руководство пользователя

Страница: 64 / 82

Replacement

- ENGLISH

Maintenance

CAUTION:

■ Do not replace the lamp unit when it is hot. (Wait at least 45 minutes after use.)

The inside of the cover can become very hot, take care to avoid burn injuries.

Notes on the replacement of the lamp unit

The luminous source of the lamp is made of glass and may burst

if you hit it against a hard surface or drop it.

Please handle with care.

A Phillips screwdriver is required for replacement of the lamp unit.

When replacing the lamp unit, be sure to hold it by the handle.

Hold the lamp unit horizontally while replacing it to prevent

fragments of glass from scattering, in case the lamp breaks.

When the projector is mounted on a ceiling, do not work directly

under the projector or put your face close to the projector. Pull the

old lamp unit out horizontally.

The lamp contains mercury. Consult your local municipality or

your dealer about correct disposal of used lamp units.

Attention

Do not use other than designated lamp units.

The part numbers of accessories and separately sold components are subject to change without notice.

When to replace the lamp unit

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the

screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly.

On screen

Lamp replacement icon

LAMP REPLACE indicator

LAMP

Over 3000 hours

Over 3200 hours

The message is displayed for 10 seconds. If you

press any button within the 10 seconds, the message

disappears.

After ten minutes, the projector shuts off the power

automatically.

Lights in yellow (even in

stand-by mode).

Note

Allow a projector to cool enough before you open the Lamp Cover. The inside of the projector can become very

hot.

The Lamp replacement icon will not appear when the Display function is set to Off (

page 53), or during

Freeze (

page 33), or AV mute (

page 34).

Содержание PT-VW330U



















































































Результаты поиска

Содержание PT-VW330U

Отзывы:

Похожие инструкции для PT-VW330U

Бренды по названию

Популярные бренды

Panasonic PT-VW330U, Руководство по эксплуатации

Результаты поиска

Содержание PT-VW330U

Отзывы:

Похожие инструкции для PT-VW330U

Бренды по названию

Популярные бренды