Panasonic Panafax UF-895, Руководство по обслуживанию

Страница: 155 / 342

Service Modes
155
018 RX START 1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps Selects the reception modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when
communicating with regular G3 machines.
When communicating with Super G3 (V.34)
machines, use Parameter No. 33.
019 ITU-T V.34 1 = Off
2 = On
3 = Select Selects whether the ITU-T V.34 is Off, On or Select.
(Select: Select whether the ITU-T V.34 is Off or On,
when entering One-Touch/Abbreviated Dialing
Numbers or Manual Number Dialing.)
020 ITU-T ECM 1 = Off (Invalid)
2 = On (Valid) Select the ECM mode.
021 EP TONE 1 = Off (without EP Tone)
2 = On (with EP Tone) Selects the echo protect tone on V.29 mode, On
(add) or Off (Not add).
(Used when Echo Suppression is disabled.)
022 SIGNAL INTERVAL 1 = 100 ms
2 = 200 ms
3 = 500 ms Selects the time interval between the receiving
signal and the transmitting signal.
023 TCF CHECK 1 = Normal (Short)
2 = Long Selects the TCF check interval Long/Short
024 CED FREQUENCY 1 = 1080 Hz (non CCITT)
2 = 2100 Hz Selects the CED frequency 2100/1080 Hz
025 COMM. START-UP 1 = 1’st response
2 = 2’nd response Selects the communication start-up condition (XMT
and Polling).
(Used when Echo Suppression is disabled.)
026 NON-STANDARD 1 = Off (Invalid)
2 = On (Valid) Selects own mode (Panafax mode).
027 SHORT PROTOCOL B 1 = Off (Invalid)
2 = On (Valid) Selects the short protocol mode.
028 SHORT PROTOCOL D 1 = Off (Invalid)
2 = On (Valid) Selects the short protocol mode.
029 REMOTE DIAGNOSTICS 1 = Off (will not accept)
2 = On (accepts) Selects whether the machine accepts the Remote
Diagnostics from the service station.
030 CED & 300 bps 1 = 75 ms
2 = 1 sec Selects the pause interval between the CED and
the 300 bps signal. (Used when Echo Suppression
is disabled.)
031 RTC = EOLx12 1 = Off (EOLx6)
2 = On (EOLx12) Selects the RTC signal, EOLx6 or EOLx12.
032 V34 TX START 2400-33600bps Selects the transmission modem start speed in
V.34 communication, 33600-2400 bps.
033 V34 RX START 2400-33600bps Selects the receiving modem start speed in V.34
communication, 33600-2400 bps.
034 V34 TX Symbol Rate 2400-3429sr Selects the transmission symbol rate for V.34,
3429/3200/3000/2800/2400 sr.
Press “
∨
“ or “
∧
“ to select the symbol rate.
035 V34 RX Symbol Rate 2400-3429sr Selects receibing symbol rate for V.34,
3429/3429/3200/3000/2800/2400 sr.
Press “
∨
“ or “
∧
“ to select the symbol rate.
036 Not Used
037 PROTOCOL DISPLAY 1 = Off (not displayed)
2 = On (displayed) Selects whether to display the modem speed
during communication. (Press “
∨
“ or “
∧
“ to display)
038 Not used
039 FLASH TIME 5 = 50 ms
~
100 = 1000 ms Selects the pause interval before activating the
Flash key.
040 E/F TIME (For Germany,
Austria and Switzerland only) 5 = 50 ms
~
100 = 1000 ms
Selects the pause interval before activating the
Flash key.
041 PAUSE TIME 1 = 1 sec.
~
10 = 10 sec. Selects the pause interval from 1 sec. ~ 10 sec. for
dialing through a switchboard or for international
calls.
042 Not used
043 REDIAL INTERVAL 0 = no waiting
~
15 = 15 minutes Selects the redial interval from 0 to 15 minutes in 1
minute steps.
Function Parameter Table
No. Parameter (see Note 3) Selections Function