Panasonic Panafax UF-585, Руководство по обслуживанию

Страница: 135 / 310

135
434 XMT or RCV B CD (response from Modem) did not turn OFF
within 180 sec. after receiver detected FLAG
signal. Remote unit is defective.
SCA/SCB PCB or LCU PCB is defective.
436 G3 RX C DCN received after transmitting FTT. Transmitter is defective or incompatible.
Line quality is poor.
456 RCV B Received relay transfer request or confidential
document to distribute to a end receiving station
or all confidential mailboxes are used.
457 RELAYXMT
CONF.XMT/
POLL B Remote unit does not have Relayed XMT or
Confidential Comm. capability.
459 RCV C Failed training in Phase C. Line quality is poor. (Training signal is distorted
due to line noise)
SCA/SCB PCB or LCU PCB are defective.
490 RCV C Sum of error line exceeded the limit (Parameter
70) by 64 lines. Line quality is poor.
SCA/SCB PCB or LCU PCB are defective.
494 RCV C Interval between two EOLs was more than 10
sec. when receiver received message data. Transmitter is defective.
Line quality is poor. (EOL is damaged due to
line noise)
SCA/SCB PCB or LCU PCB are defective.
495 XMT/RCV C During reception, CD turned OFF or continued
ON for long time.
During communication, lost loop - current. Line is disconnected.
Transmitter is defective.
SCA/SCB PCB or LCU PCB are defective.
496 XMT C CS of modem is not able to turn ON. SCA/SCB PCB is defective.
501 XMT/
RCV(V.34) B Remote unit does not have Modem
compatibility.
502 XMT/
RCV(V.34) B,C,D During reception, CD turned OFF or continued
ON for long time.
During communication, lost loop - current. Line is disconnected.
Transmitter is defective.
SCA/SCB PCB or LCU PCB are defective.
503 XMT/
RCV(V.34) B,C,D CS of modem is not able to turn ON during
training. SCA/SCB PCB is defective.
Line is disconnected.
504 RCV/V.34
(Polling) B Polling is rejected from the remote station. No polling document is set.
505 XMT/V.34
(Polling) B Polling XMT is rejected. No polling document is set.
540 XMT ECM B No response after transmitting 3rd CTC or DCN
received. Incompatible interface.
541 XMT ECM D No response after transmitting 3rd EOR or
received DCN. Line is faulty.
LCU PCB abnormal.
542 XMT ECM D No response to the 3rd RR transmitted or
received DCN. Remote unit is abnormal.
543 XMT ECM D T5 timer (60 sec.) elapsed without MCF. Remote unit is abnormal.
544 XMT ECM D Stopped Transmission after EOR Transmission. Line is faulty.
LCU PCB abnormal.
550 RCV ECM C Timer between frames in phase C has elapsed. Defective remote station.
554 RCV ECM D Transmitted ERR after receiving EOR. Faulty line.
555 RCV ECM D Transmitted PIN after receiving EOR. Faulty line and Operator Call requested by RX
side.
570 RCV B Password or machine code did not match during
remote diagnostic communication.
571 XMT B Remote unit did not have the remote diagnostic
function.
580 XMT B Sub-address transmission to a unit that has their
DIS bit 49 (NSF bit 155) OFF. Sub-address transmission to a unit that has no
Sub-address function.
581 XMT B Sub-address Password transmission to a unit
that has their DIS bit 50 (NSF bit 156) OFF. Sub-address transmission to a unit that has no
Sub-address function.
601 XMT ADF Door was opened during ADF
transmission.
623 XMT A No document was in the ADF. (Built-in dialer
engaged) Operator removed the document from the ADF
after dialing was completed.
Document is not set properly in the ADF.
630 XMT or
RCV(Polling) B Redial count over. No dial tone detected.
Sensor dial tone is not detected. (country
dependent)
Busy tone is detected. (country dependent)
T1 timer (35±5 sec) elapsed without a signal
from the receiver.
631 XMT A "STOP" button was pressed during Auto Dialing.
Information Codes
Code Mode Phase Description of Problem Cause