background image

CLASSIFICATION 
Einstufung 

 

No. 
DS-Eval4570-2400 

REV. 

SUBJECT 
Thema 

EvalBoard PAN4570 

 

PAGE 
Seite 

 

10  of  20 

CUSTOMER’S CODE 
EvalPAN4570 

PANASONIC’S CODE 
 

DATE 
Datum 

 

06.11.2006 

 

 

European Technology Center 

Panasonic Electronic Devices (EUROPE) GmbH 

APPROVED 

genehmigt 

CHECKED 

geprüft 

DESIGNED 

Erstellt 

 

8.3.   SELECTING THE HARDWARE PLATFORM 

 

The EmberZNet stack uses a Ember

TM

 platform (Ember

TM

 breakout board and RCM  

module), which   is defined in a BOARD_HEADER file. This file is named dev0455.h  and 
located in the folder 
 ….\Ember\EmberZNet2.5.0\hal\micro\xap2b\em250\board\  
 

IMPORTANT:

 Because the use and settings of GPIOs on the PAN4570 testboard is 

different another BOARD_HEADER file is required.  
 
After installation of EmberZNet2.5.0 the required change of the BOARD_HEADER file 
can be done as follows: 
 
Rename the dev0455.h extracted with EmberZNet for example in dev0455_ember.h 
Copy the PAN4570.h file from the cd to the location where dev0455.h was located 
Rename the PAN4570.h file to dev0455.h 
 
PAN4570.h enables D11, D14, SW2 and SW6 connected to PAN4570 for the use of 
the “simple-lighting” sample application. 
 
The two switches and two LEDs are used as follows: 

 

board LED 

GPIO 

Ember

TM

 name 

function 

LIGHT D11 

HEARTBEAT_LED 

heartbeat 

LIGHT D14 

12  LIGHT 

LIGHT 

LIGHT 

SW2 

15 

BUTTON 1 

LIGHT ON and networking 

LIGHT 

SW6 

BUTTON 0 

LIGHT OFF and networking 

SWITCH 

SW2 

15 

BUTTON 1 

LIGHT ON 

SWITCH 

SW6 

BUTTON 0 

LIGHT OFF 

         (Table 

4) 

For custom applications 5 buttons and 4 LEDs are available on the testboard, the 
carrierboard/testboard schematics in part 10 show their connections to the GPIOs. 
Changes regarding the GPIOs should always be done only in the BOARD_HEADER file. 
 

 

 

 

 

 

 

Содержание PAN4570





















Отзывы: