No
Terminal Name
I/O
Description
P.OFF
P.Failure
Reset/
Release
1
CODE1
I
AD input terminal for model setting.
In
In
In
2
CODE2
I
AD input terminal for model setting.
In
In
In
3
T-PHOT
I
Input terminal of the Tape Beginning sensor detection.
*More than 2.6V : Black tape part. *Less than 2.4V :Trans. Tape part.
In
In
In
4
SAFETY_CYL
I
REG 12V short detection signal.
It is a measure for cylinder driver over heat by short.
Perform detection process at 3 seconds after that the P.ON (H) signal at Pin 4 of IC6001
has been shifted from Low to High.
[Detection method]
When the terminal voltage is less than 3.0V during 3 seconds continuously, the power is
turned off compulsorily.
* When a cassette is in, the power is turned off after a few second delay for the
mechanism initial function.
* Key/Remote controller input is inhibited while the compulsory power off process.
In
In
In
5
KEY1
I
AD input terminal for KEYs on the VCR.
In
In
In
6
KEY2
I
AD input terminal for KEYs on the VCR.
In
In
In
7
S-PHOT
I
Input terminal of the Tape End sensor detection.
*More than 2.6V : Black tape part. *Less than 2.4V :Trans. Tape part.
In
In
In
8
NC
O
Low fix.
Low
Low
Low
9
TRACKING_ENVE
I
Input terminal of the Video envelope signal.
In
In
In
10 SQPB/SE/VHS
I
VV: VHS: 50Hz & 0~1.25V
60Hz
MESCAM: 50Hz & over than 1.25V
EE: VHS: 50Hz & 0~1.25V
60Hz
MESCAM: 50Hz & over than 1.25V
In
In
In
11 CURRENT.LIMIT
O
Control terminal for the Capstan current limit.
(Output impedance: MIN:1K, TYP:2.5K, MAX:4.0K)
In
DA=0V
Low
In
DA=0V
12 EEPROM_CS
O
Chip Select output terminal for EEPROM
*Active High output.
Low
Low
Low
13 ART.V/H/N
O
Output terminal for the Artificial V-sync.
1. In trick playback.
Artificial V sync inserting timing : High
Artificial H sync inserting timing : Hi-Z (M output)
Except above conditions : Low
2. Other than above conditions (Including OSD REC) : Low
Low
Low
Low
14 REMOCON
I
Input terminal for the Remote Controller.
In
In
In
15 NC
O
Low fix.
Low
Low
Low
16 NC
O
Low fix.
Low
Low
Low
17 NC
O
Low fix.
Low
Low
Low
18 VIDEO.H.SW
O
Video head switching signal
*L'/R="High" *R'/L="Low"
Low
Low
Low
19 AUDIO.H.SW
O
Head switching signal for Audio circuit.
Low
Low
Low
20 D.A.REC(H)
O
Recording control signal for the Linear Audio.
Low
Low
Low
21 TAPE REFRESH (H)
O
Terminal for the signal that changes FE oscillation frequency (130KHz/70KHz) for TAPE
REFRESH.
*TAPE REFRESH is operating: "High" is output
*Other than above condition: "Low" is output
Low
Low
Low
22 PICT1
O
Control terminal for the Picture mode.
Low
Low
Low
23 PICT2
O
Control terminal for the Picture mode.
Low
Low
Low
24 NC
O
Low fix.
Low
Low
Low
25 SP(L)
O
REC MODE DATA
*N2H/P3H:"Low"
*N4H/N6H/P6H/P9H:"High"
Low
Low
Low
26 STAB(L)
I
SAFETY TAB DETECTION
*With SAFETY TAB: "Low"
*Without SAFETY TAB:"High"
In
In
In
27 NC
O
Low fix.
Low
Low
Low
28 NTSC (L)
O
PLAYBACK MODE…..50Hz:"High", 60Hz:"Low"
Low
Low
Low
Содержание NV-SJ30AM
