VCR Mode
-29-
Audio Dubbing
You can add music or narration to the recorded Cassette.
≥
If the tape recorded in the [16bit] Mode is dubbed with the
Audio Dubbing function, the original sound is erased. (If
you wish to preserve the original sound, use the [12bit]
Mode when recording.)
≥
Audio Dubbing cannot be performed on a recording done in
LP Mode. (
1
Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >>
[AV JACK] >> [IN/OUT].
2
Continuing the aforesaid setup, select [A.DUB INPUT]
>> [MIC] or [AV IN].
≥
Set to [AV IN] when external device is used, and to [MIC]
when an external or built-in microphone is used.
≥
Switch the Movie Camera over to the Still Playback
Mode where you want to add new sound.
3
on the Remote
Controller.
4
To start Audio Dubbing, press the [
;
] Button
on
the Remote Controller.
To Cancel Audio Dubbing
Press the [
;
] Button
The Movie Camera is in the Still Playback Mode again.
To dub audio while listening to a pre-recorded sound
When pausing the audio dubbing, [12bit AUDIO] on the
[PLAYBACK FUNCTIONS] Sub-Menu is automatically set to
[ST2] and you can check the pre-recorded sound. When a
microphone is used for audio dubbing, use headphones to
listen to the pre-recorded sound while dubbing the audio.
(When using headphones, set [AV JACK] on the
[AV IN/OUT SETUP] Sub-Menu to [OUT/PHONES].) When
the line input is used, you can dub audio while listening to a
pre-recorded sound from the speaker.
To Play Back the Sound Recorded by 12bit Audio
Dubbing
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >>
[12bit AUDIO] >> [ST2] or [MIX].
ST1: It plays back only the original sound.
ST2: It plays back only the sound added by Audio Dubbing.
MIX: It plays back both the original sound and the sound
added by Audio Dubbing simultaneously.
≥
For other notes concerning this item, see
Audio Level Adjustment
You can adjust the Audio Level for audio dubbing by
selecting a desired setting for [AUDIO LEVEL] on the
[RECORDING SETUP] Sub-Menu of the
[VCR FUNCTIONS] Main-Menu.
M E N U
PUSH
SHUTTER/IRIS/
VOL/JOG
INDEX
INDEX
SELECT
STOP
K
L
∫
V
/REW
STILL ADV
T
W
s
VO
L
r
¥
REC
MULTI/
P-IN-P
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
6
1
5
;
E
D
When you set [MODE] of [AUDIO LEVEL] to any other
setting than [AUTO], the Audio Level Indication appears.
Adjust the [GAIN] value.
When this setting is changed, the [MIC LEVEL ADJ.] setting
on the [ADVANCED FUNCTIONS] Sub-Menu of the
[CAMERA FUNCTIONS] Main-Menu will likewise be
changed.
For details, refer to Microphone Sensitivity Level Adjustment
(
To Reduce the Sound Distortion
Lower the output level of the external audio device. Or, set
the [MODE] of [AUDIO LEVEL] to [AUTO] or [MNL(AGC)].
Copying on an S-VHS (or a VHS) Cassette
(Dubbing)
After connecting the Movie Camera and the VCR as
illustrated, start the following procedures.
1
AV Cable
2
S-Video Cable (not supplied)
≥
If your TV is not equipped with AV Input Sockets, the 21-pin
Adaptor (purchase separately) is necessary. Consult your
dealer.
≥
Be sure to press the [OSD] Button (
) on the Remote
Controller prior to copying so that no indications are visible.
Otherwise, the displayed tape counter and function
indications are also copied.
Movie Camera:
1
Insert the recorded Cassette.
VCR:
2
Insert an unrecorded Cassette with an erasure
prevention tab.
≥
If various setups (such as external input, tape speed,
etc.) are required, please refer to the operating
instructions of your VCR.
Movie Camera:
3
Press the [
1
] Button to start playback.
VCR:
4
Start recording.
5
Press the Pause or Stop Button to stop recording.
AUDIO LEVEL SETUP
PRESS MENU TO RETURN
MODE AUTO MNL MNL
(AGC) (NO-AGC)
(dB) -30 0 +6
|||||||||-----
GAIN
21-pin Adaptor
MIC
AV IN/OUT
PHONES/REMOTE
USB/
EDIT
D
(MINI)
S-VIDEO
IN/OUT
1
2
[VIDEO IN]
[AUDIO IN]
[S-VIDEO IN]
B5-B.book 29 ページ ２００２年８月６日 火曜日 午前１１時３３分
