5
Tuning the TV to Your VCR
The VCR supplies a signal to the TV via the RF coaxial cable
on channel E21-E69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV]
(2)
.
Preparation
• Turn on the TV and the VCR.
Operations
1 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
• Set [RF SELECT] by pressing [
2 1
]
(28)
to select the
colour TV system used by the TV set to be connected.
BG:
PAL B.G.H/SECAM B.G
I:
PAL I
DK:
PAL D/SECAM D.K.K1
2 Press [MENU]
(9)
.
• If Auto Tuning stops halfway, refer to the right, “To Restart
Plug in Auto Tuning”.
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU]
(9)
for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
2 Enter the desired channel number (E21-E69) by
[Numeric]
(3)
or [Channel]
(20)
.
• Set the RF output channel of the VCR to [
ss
] (RF OFF) when
the VCR is connected to the TV via the Audio/Video cable.
Press [Channel]
(20)
to display [
ss
].
• It is also possible to select by pressing [Numeric]
(3)
.
Example:
3 Press [MENU]
(9)
to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
Storing TV Broadcasts in Your VCR
The VCR is fitted with its own tuner (just like a normal TV) and
can be preset to receive up to 99 TV broadcast stations.
Plug in Auto Tuning
When the VCR is turned on after connecting the aerial cable
and the mains lead, Auto Tuning starts.
Auto tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position.
To Cancel Auto Tuning Mid-Operation:
Press [MENU]
(9)
during Auto Tuning.
If Auto Tuning stops halfway, follow the next procedures to
restart Plug in Auto Tuning.
To Restart Plug in Auto Tuning:
If Auto Tuning stops halfway by cancelling or playback;
1 Press [EJECT]
(35)
and remove the video cassette.
2 Keep both [Channel]
(20)
I
and
J
on the VCR
pressed simultaneously for 3 seconds or more during
the VCR on.
• The channel displayed on the VCR display disappears for
a moment then changes to 1.
3 Disconnect the mains lead and then reconnect it.
4 Turn off the VCR and then turn it on.
• Auto Tuning commences.
If Auto Tuning stops halfway by turning the VCR off or a
power failure,
Or if the VCR is turned on without the aerial connected
and all channels are skipped:
1 Disconnect the mains lead and then reconnect it.
2 Turn off the VCR and then turn it on.
• Auto Tuning commences.
CH 22
SEARCH
END: MENU
21
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
RF SELECT
BG I [DK]
END: MENU
AUTO TUNING IS
COMPLETED.
RF SELECT:
During Plug in Auto Tuning
After Plug in Auto Tuning
Panasonic VCR
END: MENU
RF SELECT:
RF SELECT
BG I [DK]
21
ss
69
(RF OFF)
2
8
28:
CH 22
SEARCH
END: MENU
21
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
NV-MV41EE_GCU.book 5 ページ ２００４年３月１日 月曜日 午後７時１４分
Содержание NV-MV41 Series
Страница 20: ...20 MEMO ...
