37
Replacement for DEFROST HEATER
1. Open vinyl bag by cutting wire band and remove wires.
2. Unhook electric wire of defrost heater.
3. Defrost heater is drawn out forward while pushing up the
Rubber cap (Land R) Hook.
4. Unhook Heater cover hook from Rubber cap.
5. Cut 2 wires of defrost heater, then connect new defrost
heater with wire joint. (Cut the wire near the wire joint
side.)
CAUTIONS
• Insert heater cover into rubber cap properly.
• Arrange the lead wire so that it will not loosen.
• Cover connectors by plastic bag. And Bind the inlet of vinyl
bag by band firmly.
CAUTION DURING INSTALLATION OF COIL COVER AS
• Put Foam tape on again when the Foam tape is teard or
come off.(Prevent to dew or frost)
• When it is installed, fit the upper side then hook the under
hooks, and fix it by 2 screws.
• The wire harness and connector are stored in the wire stor-
age.
• The Coil Cover Assy is needed to fit in firmly. Otherwise you
cannot install the Barrier Assy VF.
• The Coil Cover Assy is needed to fit in firmly. Otherwise it is
become cause of dew or frost.
12.4.2.
SENSOR FCC
1. Remove Coil cover Assy.
(Refer to "Disassembly of VC and FC compartment".)
2. Come off the aluminium tape what is fixed Coil Cover INS
Assy and Coil Cover Heater, Coil Cover B.
3. Cut seal tape by cutter (two point of "A-1",”A-2” ),
between coil cover F and Coil cover INS Assy.
4. Unhook 8 portions hooking of Coil Cover F, then remove
Coil Cover F.
5. Unhook 4 portions hooking of under side Coil Cover, then
remove Coil Cover F.
6. Remove Sensor FCC from Hook of Sensor FCC fixing
point on Coil cover F.
Cautions and how to install exchanged parts
• New Sensor FCC is installed back side of Coil Cover F as
before, and hook 8 portions hooks of Coil Cover B.
• Put aluminium tape on upper side of Coil Cover Heater Assy,
and INS Coil Cover Assy to fix.
• Reform at part of seal(A-1, A-2) by attached foam tape.
• Cut the wires of New Sensor FCC appropriate length, and
connect these wires by Scotch Lock.
• Install Coil Cover Assy, then wires and connectors are
stored in storaged parts of connector.
12.4.3.
FAN MOTOTR FC
1. Remove Coil cover Assy.
a. (Refer to "Disassembly of VC and FC compartment 1-
3".)
b. (Refer to "Disassembly of SENSOR FCC 1-5")
2. Remove Paper tape which fixing fan motor cord. Remove
Foam tape which connecting Coil cover INS Assy and
Coil cover B.
Содержание NR-F532TT
