Panasonic NR-B32FW3 Скачать руководство пользователя | Manualshive

Страница: 36 / 52

background image

36

2. Remove four screws and take Cover Coil A'ssy out.

Remove sensor FC from the hook of reverse side of
Cover Coil FC, and replace new one.

11.4.2. SENSOR DEFROST, TEMPERA-

TURE FUSE A’SSY AND DEFROST
HEATER A'SSY

1. SENSOR DEFROST

a. Remove Holder Def Sensor that is installing upper

side of Accumulator.

b. Remove Sensor Defrost from Holder Def Sensor.

c. Pull Bag Joint from storage position of upper side.

Cut Cable Tie of Bag Joint, then take out wires and
connectors from its inside.

d. Peal off the tape which bundled wires. Remove the

connector of Sensor Defrost, only press and pull, then
replace new good one.

NOTES ON INSTALLATION OF SENSOR DEFROST

• Install Sensor Defrost in Holder Def Sensor, then install

Holder Def Sensor in upper side of Accumulator as
before.

• Tighten Bag Joint that is put in the connector of Sensor

Defrost with other connectors by Cable Tie as before.

• Store Bag Joint to the place as before.

«
...
34
35
36
37
38
...
»

Содержание NR-B32FW3





















































Отзывы:

Нет отзывов

Похожие инструкции для NR-B32FW3

Бренд: Danby Страницы: 21

Бренд: Danby Страницы: 40

Бренд: Zanussi Страницы: 8

Бренд: Zanussi Страницы: 36

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 24

Бренд: Dacor Страницы: 2

Бренд: Infiniton Страницы: 30

Бренд: U-Line Страницы: 51

Бренд: Indesit Страницы: 12

Бренд: Newworld Страницы: 28

Бренд: Avanti Страницы: 21

Бренд: Vinotemp Страницы: 9

Бренд: Gibson Страницы: 19

Бренд: Magic Chef Страницы: 10

Бренд: Caple Страницы: 28

Бренд: U-Line Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды