background image

3

TABLE OF CONTENTS

1.

CONTROL PANELS ................................................................................................................................................. 4

2.

OPERATION AND DIGITAL PROGRAMMER CIRCUIT TEST PROCEDURE ....................................................... 5

3.

SCHEMATIC DIAGRAM........................................................................................................................................... 8

4.

DESCRIPTION OF OPERATING SEQUENCE ........................................................................................................ 9
4.1

Variable power cooking control ........................................................................................................................ 9

4.2

Grill cooking ..................................................................................................................................................... 9

4.3

Combination cooking........................................................................................................................................ 9

4.4

Autoweight defrost, autoweight cook ............................................................................................................... 9

4.5

Auto Sensor cook NN-V689WB ..................................................................................................................... 10

5.

CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING........................................................................... 11
5.1

Check the grounding ...................................................................................................................................... 11

5.2

Inverter Warnings .......................................................................................................................................... 11

5.3

When parts must be replaced, remove the power plug from the outlet.......................................................... 12

5.4

When the 10A fuse is blown due to the operation of short switch:................................................................. 12

5.5

Avoid inserting nails, wire, etc. through any holes in the unit during operation.............................................. 12

5.6

Confirm after repair ........................................................................................................................................ 12

6.

DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE ............................................................................ 13
6.1

Magnetron ...................................................................................................................................................... 13

6.2

Inverter Power Supply(U) .............................................................................................................................. 13

6.3

Digital Programmer Circuit (DPC) and membrane key board. ....................................................................... 14

6.4

Low voltage transformer and/or power relays (RY1)...................................................................................... 14

6.5

Fan Motor....................................................................................................................................................... 14

6.6

Door disassembly........................................................................................................................................... 15

6.7

Turntable motor.............................................................................................................................................. 15

6.8

Quartz heater ................................................................................................................................................. 15

6.9

Steam Sensor NN-V689WB........................................................................................................................... 16

7.

COMPONENT TEST PROCEDURE....................................................................................................................... 17
7.1

Primary Latch Switch, Secondary (Secondary Latch Switch and Power Relay B) Interlocks. ....................... 17

7.2

Short Switch & Monitor Circuit  ...................................................................................................................... 17

7.3

Magnetron ...................................................................................................................................................... 17

7.4

Push button key board ................................................................................................................................... 17

7.5

Inverter Power Supply (U).............................................................................................................................. 18

7.6

Inverter Power supply (U)  ............................................................................................................................. 18

7.7

Steam Sensor and digital programmer circuit ................................................................................................ 18

8.

MEASUREMENTS AND ADJUSTMENTS ............................................................................................................. 19
8.1

Installation of Primary latch switch, Secondary latch switch and Short switch............................................... 19

8.2

Measurement of microwave output ................................................................................................................ 19

9.

TROUBLESHOOTING GUIDE  .............................................................................................................................. 20

10. EXPLODED VIEW AND PARTS LIST ................................................................................................................... 24
11. PARTS LISTS ......................................................................................................................................................... 25
12. DOOR ASSEMBLY ................................................................................................................................................ 26
13. ESCUTCHEON BASE ASSEMBLY ....................................................................................................................... 27
14. PACKING AND ACCESSORIES............................................................................................................................ 28
15. TRIM KIT PARTS LIST........................................................................................................................................... 29
16. DIGITAL PROGRAMMER CIRCUIT ...................................................................................................................... 30
17. DIGITAL PROGRAMMER CIRCUIT - PARTS LIST .............................................................................................. 32

FEATURE CHART

FEATURES

NN-V659 NN-V629

NN-V689

Microwave

6

6

Grill

3

3

Combination

3x3

3 x 3

Weight Defrost 

3

3

Weight Combination

10

-

Stage Cooking

3 stage

3 stage

Delay Stand

Yes

Yes

Clock

12 Hrs

12 Hrs

Word Prompt

English

English

Weight Reheat

2

-

Weight Cook

2

-

Sensor Reheat

-

2

Sensor Cook

-

6

Sensor Combination

-

6

Содержание NN-V659WB





































Отзывы: