Panasonic NN-C2000P Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 42

background image

8.4. Fan motor

1. Disconnect 2 lead wires from fan motor terminals.

2. Disconnect 2 lead wires from fuse holder terminals. (some

models)

3. Remove 4 screws holding fan motor and orifice assy and

detach the orifice assy with fan motor from oven assy.

4. Remove fan blade from the fan motor shaft by pulling it

straight out.

5. Separate the fan motor from the orifice assy by freeing 2

catch hooks on the orifice assy.

8.5. Heater

1. Remove lead wires from lead wire holders.

2. Remove belt from pulleys of circulation fan.

3. Remove 2 screws holding heater fan motor bracket.

4. Remove 1 screw holding exhaust guide.

5. Remove 2 screws holding oven temp sensor.

6. Disconnect 2 lead wires from heater terminals.

7. Remove 4 screws holding the both sides of heater unit and

lift it up carefully.

8. Remove 3 screws holding heater supports and detach the

heater.

8.6. Door assemble

1. Open the door and remove 4 screws holding door C.

15

NN-C2000P / NN-C2000W

«
...
13
14
15
16
17
...
»

Содержание NN-C2000P











































Отзывы:

Нет отзывов

Похожие инструкции для NN-C2000P

Бренд: GE Страницы: 5

Бренд: GE Страницы: 2

Бренд: Oster Страницы: 33

Бренд: Russell Hobbs Страницы: 40

Бренд: Daewoo Страницы: 40

Бренд: FAURE Страницы: 36

Бренд: Adler Europe Страницы: 20

Бренд: Klarstein Страницы: 184

Бренд: Daewoo Страницы: 17

Бренд: Daewoo Страницы: 32

B44S32 3GB Series

Бренд: NEFF Страницы: 24

B15E54 0GB Series

Бренд: NEFF Страницы: 28

B5ACM7H 0B Series

Бренд: NEFF Страницы: 44

B25CR22 1B Series

Бренд: NEFF Страницы: 44

B47CS36 0B Series

Бренд: NEFF Страницы: 48

B48FT38 0B Series

Бренд: NEFF Страницы: 60

B45E54 0 Series

Бренд: NEFF Страницы: 28

Бренд: NEFF Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды