background image

5.  INSTALLATION

Connect.

Elbow

Do not direct the 
elbow upward.

Insert all the way.

Slide the hose band in 
the arrow direction.

 

Slide all the way until 
it stops.

Hose band

NOTE

 

Do not put the 
hose tip under 
water.

 

Do not raise the 
hose higher than 
10 cm above the 

fl

 oor.

10 cm or 
less

 

Do not extend the 
overall length to 
more than 3 m.

3 m or less

 5.1 Check the location.

 

Avoid the following locations for installation.

•  Locations with a possibility of freezing
•  Damp locations or locations where it may be 

exposed to rain, etc.
(To prevent electric shock or 

fi

 re)

•  Locations exposed to direct sunlight 

(To prevent malfunction or deformation)

•  Uneven or unstable locations (on blocks, 

timbers, a table with wheels, etc.)

5.2 Attach the bottom cover.

Insert the bottom 
cover along the 
guides.

Fix with 2 screws.

Screw

 5.3 Attach the external drain water hose.

Water supply 
hose

Water tap 
adaptor

Water supply 
valve screw

Bottom cover

External drain 
water hose

- 7 -

Service NA-F100A2.indd   7

Service NA-F100A2.indd   7

4/26/2559 BE   11:50 AM

4/26/2559 BE   11:50 AM

Содержание NA-F100A2





























Отзывы: