Panasonic MINAS A5E Series, Руководство по эксплуатации, Страница: 20 / 27

− B39 − − B38 −
English
LABEL
Terminal cover
(transparent)
2–ø4.5
R Cx
Cx
Cy
L L
Cy
2–ø4.5 x 6.75
53.1
±
1.0
100.0
±
2.0
88.0
75.0
5.0
12.0
10.0
50.0 60.0
7.0
2.0
(11.6)
(13.0)
6-M4
2
1 3
4
Circuit diagram
IN OUT
LABEL
A
B
C
H
10
F
E D
G
M4
Cover
Body
4
5
1
2
6 3
L1
Cx1
IN OUT
R Cx1
Cy1
Earth terminal
M4
Screw for cover
M3
A B C D E F G H
115 DV0PM20042
<DV0PM20042, DV0P4220> <DV0PM20043>
105 95 70 43 10 52 5.5
145 DV0P4220 135 125 70 50 10 52 5.5
165 DV0PM20043 136 165 90 80 40 54 5.5
Circuit
diagram
[Size]
[Unit: mm]
[Unit: mm]
LABEL
A
C
B
H
M5
E
F
D
Earth
terminal
M4
Screw for
cover
M3
G
Cover
Body
For single phase application, use 2 terminals among 3 terminals,
leaving the remaining terminal unconnected.
7. Conformity to EC Directives and UL Standards
Composition of Peripheral Equipments
Installation Environment
Use the servo driver in the environment of Pollution Degree 1 or 2 prescribed in IEC-
60664-1 (e.g. Install the driver in control panel with IP54 protection structure.)
Caution
Use options correctly after reading Operating Instructions of the options
to better understand the precautions.
Take care not to apply excessive stress to each optional part.
Power Supply
100 V type : Single phase, 100 V +10 % to 120 V +10 % 50/60 Hz
(A to C-frame)
–15 % –15 %
200 V type : Single/3-phase, 200 V +10 % to 240 V +10 % 50/60 Hz
(A to D-frame)
–15 % –15 %
200 V type : 3-phase, 200 V +10 % to 230 V +10 % 50/60 Hz
(E, F-frame)
–15 % –15 %
(1) This product is designed to be used in over-voltage category (installation category)
III of EN 61800-5-1:2007.
(2) Use an insulated power supply of DC12 to 24 V which has CE marking or complies
with EN60950.
Circuit Breaker
Install a circuit breaker which complies with IEC Standards and UL recognized (Listed
and marked) between power supply and noise filter.
Integral solid state short circuit protection does not provide branch circuit protection.
Branch circuit protection must be provided in accordance with the National Electrical
Code and any additional local codes.
Noise Filter
When you install one noise filter at the power supply for multi-axes application, consult with
manufacturer of the noise filter. If sufficient noise margin is required, connect 2 filters in series.
• Optional parts
Option part No.
Voltage specifications
for driver
Manufacturer’s
part No.
Applicable
driver (frame)
Manufacturer
DV0P4170 Single phase 100 V/200 V SUP-EK5-ER-6 A and B-frame Okaya Electric Ind.
7. Conformity to EC Directives and UL Standards
Composition of Peripheral Equipments
Metallic control box
Controller
Insulated power supply
for interface
Power
supply
Surge
absorber
Noise filter
Noise filter for signal lines
*1
Ground (PE)
L1
U
X4
XA
XB
X6
M
RE
V
W
L2
L3
L1C
L2C
Noise filter for
signal lines
Noise filter for
signal lines
Noise filter for
signal lines
Noise filter for signal lines
Driver
Motor
Residual
current
device
(RCD)
Circuit
breaker
*1 A to D-frame: Noise filter for signal lines, E, F-frame: Noise filter for signal lines <Power supply cable>
Option part No.
Voltage specifications
for driver
Manufacturer’s
part No.
Applicable
driver (frame)
Manufacturer
DV0PM20042
3-phase 200 V
3SUP-HU10-ER-6
A, B-frame
Okaya Electric Ind.
Single phase 100 V/200 V
3-phase 200 V
C-frame
DV0P4220 Single/ 3-phase 200 V 3SUP-HU30-ER-6 D-frame
DV0PM20043 3-phase 200 V 3SUP-HU50-ER-6 E-frame