background image

© 2008 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.

Order No.VCD0802004CE

Vacuum Cleaner

Model No.

MC-CG487-ZC79
MC-CG487-ZA76
MC-CG487K-ZP47

Product Color :Metalic blue
Destination

:Europe

TABLE OF CONTENTS

PAGE

PAGE

1 Specifications

-----------------------------------------------------

2

2 Location of Controls and Components

-------------------

3

3 Troubleshooting Guide

-----------------------------------------

5

4 Disassembly and Assembly Instructions

----------------

6

4.1. Dust box cover assembly removal -------------------- 6
4.2. Separate the upper and lower body units ----------- 6
4.3. Printed circuit board assembly (P.C.B Ass’y)

removal------------------------------------------------------- 7

4.4. Motor removal ---------------------------------------------- 8
4.5. Cord reel partition unit replacement ------------------ 9
4.6. Rail base U replacement -------------------------------10
4.7. Spring-loaded cord reel pre-winding-----------------10
4.8. How to disassemble the turbine nozzle-------------10

5 Wiring Connection Diagram

---------------------------------

12

6 Exploded View and Replacement Parts List

-----------

13

6.1. EXPLODED VIEW (ATTACHMETS)-----------------13
6.2. PARTS LIST (ATTACHMETS)-------------------------14
6.3. EXPLODED VIEW (BODY UNIT) --------------------15

6.4. PARTS LIST (BODY UNIT)---------------------------- 16
6.5. PACKING INSTRUCTIONS --------------------------- 17
6.6. PACKING LIST ------------------------------------------- 18

Содержание MC-CG487-ZA76












Отзывы: