Panasonic LX-TD500 Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 388

background image

Group

176

Programming Guide

Parameter

[UCD Setting] Supervisor Extension

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the Supervisor Extension per UCD Group.
The extension specified as the Supervisor Extension can monitor
the number of waiting calls (calls placed in the waiting queue).

Reference

• 1.3 System Features (F/G)

– Extension Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

Parameter

[UCD Setting] LOGIN Monitor

Default

Disable

Value Range

1.

Disable

2.

Enable

Description/Function

Specifies whether the extension can monitor (through the
corresponding DSS buttons) the Login / Logout status of UCD
Group members or not.

Reference

• 1.3 System Features (F/G)

– Extension Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

• 4.3.81 UCD Monitor Mode (U/M)

«
...
174
175
176
177
178
...
»

Содержание LX-TD500





































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LX-TD500

Бренд: MANCO Страницы: 57

Бренд: MANCO Страницы: 57

Бренд: Irbis Страницы: 99

Бренд: Land Pride Страницы: 132

Бренд: Hisun Страницы: 116

Бренд: Can-Am Страницы: 152

Outlander X mr Series

Бренд: Can-Am Страницы: 196

Бренд: LONCIN Страницы: 156

Бренд: Toro Страницы: 32

Honda Rancher 324200C550

Бренд: Yoshimura Страницы: 6

Бренд: Landoll Страницы: 64

Бренд: GAS GAS Страницы: 142

MKII 600 Series

Бренд: NC ENGINEERING Страницы: 80

Бренд: Yamaha Страницы: 87

DS 250 2023 Series

Бренд: Can-Am Страницы: 172

Бренд: Metal-Fach Страницы: 32

Бренд: Tao Motor Страницы: 80

Бренд: Ironhorse Trailers Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды