Panasonic LP-M Series Скачать руководство пользователя

Страница: 9 / 174

Related Regulations and Standards

Applicable regulations and standards

This product meets the requirements mandated by the following regulations and standards.

Note that our products do not conform to the regulations and standards of the countries and regions not mentioned in this

section. When exporting the product by itself or integrated into machine or device, confirm the regulations and standards of

the exporting country or region.

Model

Applicable regulations and standards

LP-M200-LS1

LP-M205-LS1

LP-M500-LS1

LP-M505-LS1

LP-MA00-LS1

LP-MA05-LS1

EN standards (CE Marking) *1

• 2014/30/EU “EMC Directive”

• EN 55011

• EN 61000-6-2

• 2006/42/EC “Machinery Directive” (for partly completed machinery) *2

• EN ISO 11553-1

• EN 60204-1

• 2011/65/EU as amended by (EU)2015/863 “RoHS Directive”

• EN IEC 63000

• EN 62321-1, EN 62321-2, EN 62321-3-1, EN 62321-3-2, EN 62321-4,

EN 62321-5, EN 62321-6, EN 62321-7-1, EN 62321-7-2, EN 62321-8

• Technical specification

• EN 60825-1

LP-M200, LP-M200-CHN

LP-M205, LP-M205-CHN

LP-M500, LP-M500-CHN

LP-M505, LP-M505-CHN

LP-MA00, LP-MA00-CHN

LP-MA05, LP-MA05-CHN

LP-MA06, LP-MA06-CHN

LP-M200-S, LP-M200-S-CHN

LP-M205-S, LP-M205-S-CHN

LP-M500-S, LP-M500-S-CHN

LP-M505-S, LP-M505-S-CHN

LP-MA05-S, LP-MA05-S-CHN

LP-MA06-S, LP-MA06-S-CHN

EN standards (CE Marking) *1

• 2014/30/EU “EMC Directive”

• EN 55011

• EN 61000-6-2

• 2014/35/EU “Low Voltage Directive”

• EN 61010-1

• EN 60825-1

• 2011/65/EU as amended by (EU)2015/863 “RoHS Directive”

• EN IEC 63000

• EN 62321-1, EN 62321-2, EN 62321-3-1, EN 62321-3-2, EN 62321-4,

EN 62321-5, EN 62321-6, EN 62321-7-1, EN 62321-7-2, EN 62321-8

LP-M200, LP-M200-CHN

LP-M205, LP-M205-CHN

LP-M500, LP-M500-CHN

LP-M505, LP-M505-CHN

LP-MA00, LP-MA00-CHN

LP-MA05, LP-MA05-CHN

LP-MA06, LP-MA06-CHN

LP-M200-S, LP-M200-S-CHN

LP-M205-S, LP-M205-S-CHN

LP-M500-S, LP-M500-S-CHN

LP-M505-S, LP-M505-S-CHN

LP-MA05-S, LP-MA05-S-CHN

LP-MA06-S, LP-MA06-S-CHN

LP-M200-LS1

LP-M205-LS1

LP-M500-LS1

LP-M505-LS1

LP-MA00-LS1

LP-MA05-LS1

JIS (Japanese Industrial Standards)

• JIS C 6802

FDA (Food and Drug Administration) regulations

• 21 CFR 1040.10 and 1040.11 (except for conformance with IEC 60825-1 Ed. 3, as

described in Laser Notice No. 56 dated May 8, 2019)

GB (China National Standard)

• GB 7247.1-2012 (idt IEC 60825-1: 2007)

KC mark (Korea Certification)

Class A Equipment (Industrial Broadcasting & Communication Equipment)

This equipment is Industrial (Class A) electromagnetic wave suitability equipment and

seller or user should take notice of it, and this equipment is to be used in the places

except for home.

A 급 기기 ( 업무용 방송통신기자재 )
이 기기는 업무용 (A 급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합니다 .

*1: Contact for CE:

Panasonic Marketing Europe GmbH, Panasonic Testing Center

Winsbergring 15, 22525 Hamburg, Germany

*2: For LP-M200-LS1, LP-M205-LS1, LP-M500-LS1, LP-M505-LS1, LP-MA00-LS1 and LP-MA05-LS1, the printed copy

of “Declaration of Incorporation of Partly Completed Machinery” is included in the package of this product.

ME-LPM-SSM-10

Содержание LP-M Series















































































































































































Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды

Panasonic LP-M Series, Руководство по обслуживанию

Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды