Panasonic LH-43RM1MX Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 51

background image

SECTION 3 ADJUSTMENTS

4.Hotel Mode Setting

4.1.Entering Hotel Mode Menu

Hotel Mode Menu should be shown by the following operation.

4.1.1. Step 1

Press “ MENU ”button once on the Remote Control,While pressing the button, press “ 7906 ” button on the Remote Control.

4.1.2. Step 2

To enable Hotel Mode, use the

◀

or

▶

arrow keys while “Hotel Mode” item is selected “On”, Once Hotel Mode is on, the

Hotel Mode settings will be enabled for adjusting.

4.1.3. Step 3

Use the ▲ and ▼ arrow keys to access the hotel mode settings. Use the

◀

and

▶

arrow keys to change the settings, See

SETTING HOTEL MODE MENU SETTINGS for explanation of hotel mode settings, MENU for return to previous menu.
Press RETURN when finished adjusting the settings.

ADJ-9

«
...
37
38
39
40
41
...
»

Содержание LH-43RM1MX




















































Отзывы:

Нет отзывов

Похожие инструкции для LH-43RM1MX

Бренд: HANNspree Страницы: 18

Бренд: ViewSonic Страницы: 53

Бренд: Partron Страницы: 25

Бренд: Graco Страницы: 32

Бренд: Alienware Страницы: 32

Бренд: Neway Страницы: 13

Бренд: B.Well Страницы: 72

Бренд: ViewSonic Страницы: 47

LOFT COMPACT VDS

Бренд: Fermax Страницы: 28

BOOSTXL-K350QVG-S1

Бренд: Texas Instruments Страницы: 10

Бренд: ViewSonic Страницы: 25

Бренд: Samsung Страницы: 39

S34C65 T Series

Бренд: Samsung Страницы: 46

Бренд: Samsung Страницы: 40

Бренд: Samsung Страницы: 44

S49C95 U Series

Бренд: Samsung Страницы: 43

S34J550WQ Series

Бренд: Samsung Страницы: 47

Бренд: Samsung Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды