not to heat too long.
- PbF solder will tend to splash if it is heated much higher than its
melting point, approximately 1100°F, (600°C).
- If you must use Pb solder on a PCB manufactured using PbF
solder, remove as much of the original PbF solder as possible and
be sure that any remaining is melted prior to applying the Pb
solder.
- When applying PbF solder to double layered boards, please check
the component side for excess which may flow onto the opposite
side (See figure, below).
1.1. Suggested PbF Solder
There are several types of PbF solder available commercially. While this product is manufactured
using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi).
Please check the manufac
turer’s specific instructions for the melting points of their products and any precautions for
using their product with other
materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product:
0.3mm, 0.6mm and 1.0mm.
1.2. How to recognize that Pb Free solder is used
1.2.1. Base Unit
1.2.1.1. Main
(Component View)
1.2.1.2. Operation
(Component View)
(Flow Solder Side View)
3
Содержание KXTG2226W - 2.4GHZ DIGITAL PHONE
