Panasonic KX-WT115CE Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

32

KX-WT115CE

(

F

)

Battery Low Confirma-

tion

-

1. Apply 2.40 V between BATT+ and BATT-.
2. Confirm that there is no flashing of Battery Icon.
3. Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4. Confirm that there is flashing of Battery Icon.

IC1, F1, C1,

R45

(

G

)* BBIC Clock Adjustment

CKM

1. Apply 2.6 V between BATT+ and BATT- with DC power.
2. Input Command “SFR”, then you can confirm the current value.
3. Check X’tal Frequency. (13.824 MHz ± 15 Hz).
4. If the frequency is not 13.824 MHz ± 15 Hz, adjust the frequency of CLK exe-

cuting the command “SFR xx xx (where xx is the value)” so that the reading of
the frequency counter is 13.824 MHz ± 15 Hz.

Note:

Clear the registered information for CS before measurement, because the Fre-
quency will not possibly get stable due to the registered information.
Pressing the button of “3” ”5” “7” “#” clears the registration.
Register to it on CS after measurement.

IC1, X1, C8,

C9

(

H

)* Transmitted Power Con-

firmation

-

Remove the Antenna before starting step from 1 to 4.

1. Configure the DECT tester (CMD60) as follows;

<Setting>

• Test mode: PP
• RFPI: 0102030405
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• RF LEVEL = -70 dBm
• PACKET: PP32Z

2. Execute the command “TST 01 02 03 04 05".
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is 19 dBm ~ 25 dBm.

IC1, DA801,
L809, R806,

R807,C805,

C806,

C810~CC813,

C820~C822,
C825, C826,
C859~C863,

C895~C897

(

I

)*

Modulation Check and

Adjustment

-

Follow steps 1 to 3 of

(H)

.

4.Confirm that the B-Field Modulation is -340±30/ +340±30 kHz/div & Modu-
lated width 660 kHz using data type Fig 31.

IC1, DA801,
L809, R806,

R807,C805,

C806,

C810~CC813,

C820~C822,
C825, C826,
C859~C863,

C895~C897

(

J

)* Frequency Offset Confir-

mation

-

Follow steps 1 to 3 of

(H)

.

4.Confirm that the frequency Offset is < ± 15 kHz.

IC1, DA801,
L809, R806,

R807,C805,

C806,

C810~CC813,

C820~C822,
C825, C826,
C859~C863,

C895~C897

(

K

)* Frequency Drift Confir-

mation

-

Follow steps 1 to 3 of

(H)

.

4.Confirm that the frequency Drift is < ± 20 kHz/ms.

IC1, DA801,
L809, R806,

R807,C805,

C806,

C810~CC813,

C820~C822,
C825, C826,
C859~C863,

C895~C897

(

L

)*

Sensitivity Receiver

Confirmation

-

Follow steps 1 to 3 of

(H)

.

4.Set DECT tester power to -88 dBm.
5.Confirm that the BER is < 1000 ppm.

IC1, DA801,
L809, R806,

R807,C805,

C806,

C810~CC813,

C820~C822,
C825, C826,
C859~C863,

C895~C897

Items

Check

Point

Procedure

Check or

Replace Parts

«
...
30
31
32
33
34
...
»

Содержание KX-WT115CE

































































Отзывы:

Нет отзывов

Похожие инструкции для KX-WT115CE

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 56

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 44

Бренд: Makita Страницы: 3

Бренд: Fanvil Страницы: 16

Бренд: Parkside Страницы: 134

Wireless Service Gateway WSG

Бренд: Unify Страницы: 39

Бренд: GE Страницы: 68

Бренд: Uniden Страницы: 68

Бренд: Doro Страницы: 20

3600 Series 3618

Бренд: Videx Страницы: 8

Бренд: Yada Страницы: 14

Бренд: Niceboy Страницы: 20

Бренд: TechMatte Страницы: 2

Бренд: Federal Signal Corporation Страницы: 12

Premium Travel Phone

Бренд: HP Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды