![background image](http://html.mh-extra.com/html/panasonic/kx-tg6561bxt/kx-tg6561bxt_service-manual_1512350058.webp)
58
KX-TG6561BXT/KX-TGA651BXT
11.6. Things to Do after Replacing IC or X'tal
If repairing or replacing BBIC (FLASH type), EEPROM and X'tal, it is necessary to download the required data such as
Programming data or adjustment data, etc in memory.
The set doesn't operate if it is not executed.
11.6.1. How to download the data
11.6.1.1. Base Unit
First, operate the PC setting according to
The Setting Method of JIG (Base Unit)
Then download the appropriate data according to the following procedures.
Note:
(*1) XX: country code, YY: revision number
“XX”, “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in
Items
How to download/Required adjustment
BBIC (IC501)
Programming data is stored in memory.
1) Make sure to connect the JIG cable, then disconnect the DC
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press the PC Enter key once.
5) After a few minutes, “Successful upgrade” is displayed on the
PC indicating downloading has finished.
6) Detach the JIG cable, then disconnect the DC Power.
7) Connect the DC Power.
8) Connect the JIG cable again, and execute the command
“getchk”, then confirm the checksum value is correct.
. If the downloading fails, start again from step 1).
9) Default batch file: Execute the command “default.bat”.
10) Country version batch file: Execute the command
“TG6561EUXXrevYY.bat”. (*1)
11) Clock adjustment: Refer to Check Point (G). (*2)
EEPROM (IC611)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
1) Change the address “0001” of EEPROM to “55” to download
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG6561EUXXrevYY.bat”. (*1)
4) Clock adjustment
X'tal (X1)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Apply 6.5V between DCP ad DCM with DC power.
2) Input Command "sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(13.824 MHz ± 100 Hz).
4) If the frequency is not 13.824 MHz ± 100 Hz, adjust the
frequency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 13.824000 MHz ± 15 Hz.
FLASH (IC601)
Voice prompt data is stored in memory.
(vary depending on country version)
1) Wait more than 15 seconds after connecting the JIG Cable.
2) Execute the command "VPDL2009 -57600 ZZ.bin"(*1).
3) Wait until. "VP file transfer complete." is displayed on the
P.C. (writing time: aprox. About 1 min)
4) Detach the JIG cable to disconnect DC Power. Then
reconnect the DC Power and confirm whether the download is
successfully completed.
Содержание KX-TG6561BXT
Страница 73: ...73 KX TG6561BXT KX TGA651BXT Memo ...
Страница 76: ...76 KX TG6561BXT KX TGA651BXT Memo ...
Страница 85: ...85 KX TG6561BXT KX TGA651BXT 15 3 Accessories A1 A2 ...
Страница 90: ...90 KX TG6561BXT KX TGA651BXT RAD KXTG6561BXT KXTGA651BXT ...