Panasonic KX-TG5671BXS Скачать руководство пользователя страница 82

Страница: 82 / 114

23 HOW TO REPLACE THE LLP (Leadless Leadframe

Package) IC

23.1. Preparation

PbF (: Pb free) Solder

Soldering Iron

Tip Temperature of 700°F ± 20°F (370°C ± 10°C)

Note:

We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with less
experience could overheat and damage the PCB foil.

Hot Air Desoldering Tool

Temperature: 608°F ± 68°F (320°C ± 20°C)

23.2. Caution

To replace the IC efficiently, choose the right sized nozzle of the hot air desoldering tool that matches the IC package.

Be careful about the temperature of the hot air desoldering tool not to damage the PCB and/or IC.

23.3. How to Remove the IC

1. Heat the IC with a hot air desoldering tool through the P.C.Board.

2. Pick up the IC with tweezers, etc. when the solder is melted completely.

Note:

Be careful not to touch the peripheral parts with tweezers, etc. They are unstable.

When it is hard to melt the solder completely, heat it with a hot air desoldering tool through the IC besides through the
P.C.Board.

KX-TG5671BXS / KX-TGA560BXS

Содержание KX-TG5671BXS



















































































































Результаты поиска

Содержание KX-TG5671BXS

Отзывы:

Похожие инструкции для KX-TG5671BXS

Бренды по названию

Популярные бренды

Panasonic KX-TG5671BXS, Руководство по обслуживанию

Результаты поиска

Содержание KX-TG5671BXS

Отзывы:

Похожие инструкции для KX-TG5671BXS

Бренды по названию

Популярные бренды