Panasonic KX-TG5671BXS Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 114

background image

15.3. 5.8GHz Converter Circuit

This block converts frequency of TX signal and RX signal.

IC801 includes TX-MIXER, RX-MIXER, PLL and VCO modules internally.

The VCO module is tuned by PLL synthesizer module, and generates 3.4GHz Local signal. Reference clock (13.824MHz) from
DSP block is supplied to pin7 of IC701.

2.4GHz TX signal from 2.4GHz Mod/Demod circuit is supplied to pin 17 of IC801, and internal TX-MIXER multiplies it by 3.4GHz
Local signal from internal VCO module, and up-converts into 5.8GHz TX signal. This 5.8GHz TX signal is output from pin 2, and
goes into the 5.8GHz PA circuit.

5.8GHz RX signal from 5.8GHz LNA circuit supplied to pin 5 of IC801, and internal RX-MIXER multiplies it by 3.4GHz Local signal
from internal VCO module, and down-converts into 2.4GHz RX signal. This 2.4GHz RX signal is output from pin 15, and goes into
the 2.4GHz Mod/Demod circuits.

Note:

The exposed GND_PLATE on the bottom of the IC801 supplies the circuit ground(s) for the entire chip. It is very important that
a good solder connection is made between this GND_PLATE and the ground plane of the PCB underlying the IC801.

66

KX-TG5671BXS / KX-TGA560BXS

«
...
64
65
66
67
68
...
»

Содержание KX-TG5671BXS



















































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TG5671BXS

Solaris VISION BLSA3

Бренд: Baby Lock Страницы: 20

Бренд: Wilson Electronics Страницы: 20

BX2 Fastracts Extractor

Бренд: IPC Eagle Страницы: 8

Бренд: Keestar Страницы: 12

Бренд: Schwamborn Страницы: 50

Бренд: ELNA Страницы: 84

Бренд: JUKI Страницы: 84

Бренд: Panasonic Страницы: 100

ZEPHIRO 1000ST HAZE

Бренд: soundsation Страницы: 28

Бренд: JUKI Страницы: 50

Бренд: JUKI Страницы: 72

Бренд: JUKI Страницы: 118

Бренд: JUKI Страницы: 92

Бренд: Nilfisk-Advance Страницы: 28

Бренд: Mitsubishi Electric Страницы: 12

Бренд: Mitsubishi Electric Страницы: 20

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Nilfisk-Advance Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды