Panasonic KX-TG2219B Скачать руководство пользователя страница 54

Страница: 54 / 64

Troubleshooting

Problem

The unit does not work.

“

No link to base

Place on cradle and

try again.

” is displayed

and an alarm tone sounds.

Static, sound cuts in/out,
fades. Interference from
other electrical units.

The unit does not ring.

The handset display is blank.

You cannot program items,
such as the dialing mode.

Remedy

•

Check the settings (p. 11–15).

•

Charge the battery fully (p. 12).

•

Clean the charge contacts and charge
again (p. 13).

•

Install the battery properly (p. 12).

•

Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.

•

Re-install the battery and place the
handset on the base unit (p. 52). Try
again.

•

You are too far from the base unit. Move
closer and try again.

•

Place the handset on the base unit and
try again.

•

Plug in the AC adaptor.

•

Raise the base unit antenna.

•

Locate the handset and the base unit
away from other electrical appliances
(p. 3).

•

Move closer to the base unit.

•

Raise the base unit antenna.

•

Press

to select a clearer channel in

the talk or speakerphone mode.

•

The ringer volume is set to OFF. Set to
HIGH or LOW (p. 18).

•

Charge the battery fully (p. 12).

•

Programming is not possible while the
unit is in the talk or speakerphone mode,
when viewing the Caller List/directory list.

•

Do not pause for over 60 seconds while
programming.

•

Move closer to the base unit.

•

may have been

pressed when you picked up the
handset. Press

(OFF)

and try again.

Содержание KX-TG2219B

































































Результаты поиска

Содержание KX-TG2219B

Отзывы:

Panasonic KX-TG2219B, Руководство по эксплуатации, Страница: 54 / 64

Результаты поиска

Содержание KX-TG2219B

Отзывы: