Panasonic KX-TG1843ALS Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 93

background image

1 ABOUT LEAD FREE SOLDER (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that
contains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn),
Silver (Ag), and Copper (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type ofsolder although, with some precautions, standard Pb solder can also be used.

Caution

•

•

•

•

PbF solder has a melting point that is 50°F ~ 70°F (30°C ~ 40°C) higher than Pb solder. Please use a soldering iron with
temperature control and adjust it to 700°F ± 20°F (370°C ± 10°C). In case ofusing high temperature soldering iron, please
be careful not to heat too long.

•

•

•

•

PbF solder will tend to splash ifit is heated much higher than its melting point, approximately 1100°F (600°C).

•

•

•

•

Ifyou must use Pb solder on a PCB manufactured using PbF solder, remove as much ofthe original PbF solder as possible
and be sure that any remaining is melted prior to applying the Pb solder.

•

•

•

•

When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See the figure below).

1.1.

Suggested PbFSolder

There are several types ofPbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the
manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials.

The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

4

KX-TG1843ALS / KX-TGA122AZS / KX-TGA121AZS

«
...
2
3
4
5
6
...
»

Содержание KX-TG1843ALS






























































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TG1843ALS

Бренд: Janome Страницы: 80

Бренд: Kärcher Страницы: 30

Бренд: Sagem Страницы: 48

Бренд: National Flooring Equipment Страницы: 25

Бренд: Kärcher Страницы: 12

Бренд: Ultratec Страницы: 11

Бренд: Numatic Страницы: 28

Бренд: Singer Страницы: 30

Бренд: IPC Eagle Страницы: 40

Бренд: JBI Страницы: 36

UnionSpecial 36200UAD52

Бренд: JUKI Страницы: 64

Бренд: Kärcher Страницы: 5

Бренд: Garden Gear Страницы: 16

Бренд: JUKI Страницы: 24

Бренд: JUKI Страницы: 8

Бренд: Sandia Plastics Страницы: 13

Бренд: Brother Страницы: 80

Бренд: Sanyo Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды