Panasonic KX-TG1843ALS Скачать руководство пользователя страница 29

Страница: 29 / 93

Items

Check

Point

Procedure

Check or

Replace Parts

(

Audio Check

1. Link with Handset.

2. Input -45dBm/1kHz to MIC ofHandset.

Measure the Level at Line I/F and distortion level.

3. Confirm that the level is -9.5dBm ± 2dBm and that the distortion level is < 5%

at TEL Line (600

Ω

Load).

4. Input -20dBm/1kHz to Line I/F.

Measure the level at Receiver ofHandset and distortion level

(*Receive volume set to second position from minimum).

5. Confirm that the level is -22.5dBm ± 2dBm and that the distortion level is <

5% at Receiver (Volume Middle, 150

Ω

Load).

IC4, CN1,SA1,

L6, L7, D3, Q4,

Q5, R23, R25,

R26, R28, R63,
R39, C41, R49,
C46, C47, R42,
R43, R44, R45,
R46, R47, R48,

C108, C109,

C40, C36, Q8,

C24, R60, R62

(

)

SP-Phone

Audio Check

1. Press SP-PHONE button.

2. Press MUTE button.

3. Input -30Bm/1kHz to Line interface. (SP-Phone volume Maximum.)

4. Measure the output level and distortion level at base speaker.

5. Confirm that the level is -3dBm ±5dBm and that the distortion level is < 5%.

6. Press MUTE button.

7. Input -45dBm/1kHz to SP-Phone MIC. (TP1-TP2)

8. Measure the output level and distortion level at line interface.

9. Confirm that the level is -0dBm ±5dBm and that the distortion level is < 5%.

IC4, IC7, D311,

R375, C312,
C313, C314,
C315, C316,
C317, C318,
C319, R308,
R311, R312,
R314, C320,
C367, D301,
R301, R302,
R303, R304,
R305, R307,
C301, C302,
C303, C304,

C305, R306

(

)

Charging Check

1. Connect Charge Contact 12

Ω

/2W resistor between and charge-.

2. Measure and confirm voltage across the resistor is 2.85V ± 0.2V.

R2, R3, R4, D6,

C180, C181,
C182, D361,

Q361, Q362,

C361, C362,
R361, R362,
R363, C322,

L13, L14

(

)

TAM Operation

Confirmation

1. TAM Confirmation (Execute the command “sendchar_VPI”)

2. Confirm the returned Value (Value is “D597EC”).

IC6, R91, R92,
C86, R33, R34

KX-TG1843ALS / KX-TGA122AZS / KX-TGA121AZS

Содержание KX-TG1843ALS






























































































Результаты поиска

Содержание KX-TG1843ALS

Отзывы:

Похожие инструкции для KX-TG1843ALS

Бренды по названию

Популярные бренды

Panasonic KX-TG1843ALS, Руководство по обслуживанию

Результаты поиска

Содержание KX-TG1843ALS

Отзывы:

Похожие инструкции для KX-TG1843ALS

Бренды по названию

Популярные бренды