Panasonic KX-TCD410ALM Скачать руководство пользователя страница 33

Страница: 33 / 109

1. Open a window of MS-DOS mode from the start-up menu.
2. Change a directory to the one with “RTX_COM” contained.
3. Type “SET_COM1” from the keyboard (when COM port 1 is used for

the connection).

4. Type “doskey”.

Note:
See the table below for frequently used commands.

Command name

Function

Example

rdeeprom

Read the data of EEPROM

Type “rdeeprom 00 00 FF”, and the data
from address “00 00” to “FF” is read out.

readid

Read ID (RFPI)

Type “readid”, and the registered ID is
read out.

writeid

Write ID (RFPI)

Type “writeid 00 18 E0 0E 98”, and the
ID “0018 E0 0E 98” is written.

setfreq

adjust Frequency of RFIC

Type “setfreq nn nn”.

hookoff

off-hook mode on Base

Type “hookoff”.

hookon

on-hook mode on Base

Type “hookon”.

Getchk

Read checksum

Type “getchk”.

Wreeprom

write eeprom

Type "wreeprom 01 23 45". "01 23" is
address and "45" is data to be written.

InitBsPIN.bat

Initial Base PIN to "0000"

Type "initBsPIN"

13. CHECK PROCEDURE (HANDSET)

13.1. Preparation

13.1.1. Equipment Required

- DECT tester: Rohde & Schwarz, CMD 60 is recommended.
- Frequency counter: it must be precise to be able to measure 1Hz

(precision;±4ppm).
Hewlett Packard, 53131A is recommended.

- DC power: it must be able to output at least 1A current under 2.4V for

Handset, 9V for JIG.

- Digital multi-meter (DMM): it must be able to measure voltage and

current.

- Oscilloscope

13.1.2. JIGs and PC

- EEPROM serial JIGs

1. I2C PCB: PQZZTCD705BX

Содержание KX-TCD410ALM














































































































Результаты поиска

Содержание KX-TCD410ALM

Отзывы:

Похожие инструкции для KX-TCD410ALM

Бренды по названию

Популярные бренды

Panasonic KX-TCD410ALM, Руководство по обслуживанию

Результаты поиска

Содержание KX-TCD410ALM

Отзывы:

Похожие инструкции для KX-TCD410ALM

Бренды по названию

Популярные бренды