Panasonic KX-TA1232 Скачать руководство пользователя страница 16

Страница: 16 / 216

General Programming Instructions

Programming Guide

1.5

User Programming Mode

Some programming items are accessible by any display proprietary telephone user in the
system.
The programming items are listed below:
[000]

Date and Time Set

[001]

System Speed Dialing Number Set

Flexible CO Button Assignment

[006]

Operator / Manager Extension Assignment

[007]

DSS Console Port and Paired Telephone Assignment

[008]

Absent Messages

[009]

Quick Dial Number Set

Entering the user programming mode

You can access these programs by entering the User Programming Mode as follows:
Before entering the mode, confirm that:

•

Your telephone is on-hook.

•

No calls are on hold at your telephone

After entering the mode, perform the same programming steps as the system programming
steps in each program address.

Note

•

If nothing is entered in five seconds after the PAUSE button is pressed, it is canceled.

•

The User Password is not shown on the display. The password can be changed by system
programming. Refer to Section [120]

User Password.

•

During the programming mode, your extension is treated as a busy extension.

•

Only one proprietary telephone can be in programming mode at any one time.

Press PAUSE + + and enter the User Password
(default: 1234)

pg.book 16

ページ

２００１年７月３日　火曜日　午後２時４４分

Содержание KX-TA1232

























































































































































































































Результаты поиска

Содержание KX-TA1232

Отзывы:

Похожие инструкции для KX-TA1232

Бренды по названию

Популярные бренды

Panasonic KX-TA1232, Руководство по программированию

Результаты поиска

Содержание KX-TA1232

Отзывы:

Похожие инструкции для KX-TA1232

Бренды по названию

Популярные бренды