Panasonic KX-FP101AL Скачать руководство пользователя страница 49

Страница: 49 / 206

7. How to output the Journal Report:

a. Press the MENU button.

b. Press "#", then " 8 " and " 4 ".

Press the START/COPY/SET button.

d. The report prints out.

Error code table:

(1) CODE

(2) RESULT

(3) MODE

SYMPTOM

Counter-
measure*

PRESSED THE STOP KEY

TX & RX

Communication was interrupted by the STOP button.

DOCUMENT JAMMED

The document paper is jammed.

NO DOCUMENT

No document paper.

THE COVER WAS OPENED

TX & RX

The cover is open.

NO RESPONSE

Transmission is finished when the T1 TIMER expires.

COMMUNICATION ERROR

DCN is received after DCS transmission.

COMMUNICATION ERROR

FTT is received after transmission of a 2400BSP training signal.

COMMUNICATION ERROR

No response after post message is transmitted three times.

COMMUNICATION ERROR

RTN and PIN are received.

COMMUNICATION ERROR

No response after FTT is transmitted.

COMMUNICATION ERROR

No post message.

COMMUNICATION ERROR

RTN is transmitted.

COMMUNICATION ERROR

PIN is transmitted (to PRI-Q).

COMMUNICATION ERROR

PIN is transmitted.

NO RESPONSE

Reception is finished when the T1 TIMER expires.

ERROR-NOT YOUR UNIT

DCN is received after DIS transmission.

COMMUNICATION ERROR

DCN is received after FTT transmission.

ERROR-NOT YOUR UNIT

DCN responds to the post message.

COMMUNICATION ERROR

DCN is received before DIS reception.

COMMUNICATION ERROR

Reception is not EOP, EOM PIP, PIN, RTP or RTN.

COMMUNICATION ERROR

No response at the other party after MCF or CFR is transmitted.

ERROR-NOT YOUR UNIT

DCN is received after CFR transmission.

COMMUNICATION ERROR

Carrier is cut when the image signal is received.

MEMORY FULL

The document was not received due to memory full.

CANCELED

The multistation transmission was rejected by the user.

COMMUNICATION ERROR

TX & RX

Modem error. For the DCN, DCN, etc. abbreviations, refer to 6.6.
MODEM SECTION.

TX=TRANSMISSION RX=RECEPTION

Most fax communication problems can be resolved by the following steps.

a. Change the transmit level. (Service code: 596, refer to 2.4.4. SERVICE FUNCTION TABLE.)

b. Change the TX speed/RX speed. (Service code: 717/718, refer to 2.4.4. SERVICE FUNCTION TABLE.)

Note*:

If the problem remains, see the following "Countermeasure" flow chart.

KX-FP101AL

Содержание KX-FP101AL















































































































































































































Результаты поиска

Содержание KX-FP101AL

Отзывы:

Похожие инструкции для KX-FP101AL

Бренды по названию

Популярные бренды

Panasonic KX-FP101AL, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP101AL

Отзывы:

Похожие инструкции для KX-FP101AL

Бренды по названию

Популярные бренды