Panasonic KX-FP101AL Скачать руководство пользователя страница 25

Страница: 25 / 206

2.2. USER RECOVERABLE ERRORS

If the unit detects a problem, one or more of the following messages will appear on the display.

• There is something wrong with the modem circuit.

• There is no space to store new stations in the EASY DIAL directory. Edit or erase

unnecessary stations.

CALL SERVICE

DISPLAY MESSAGE

CAUSE AND REMEDY

• There is something wrong with the unit. Contact our service personnel.

[This error is displayed when the thermal head does not warm up. Check the thermistor
on the thermal head and connector lead. (for technicians)]

• The cover is open. Close it.

• The document is not fed into the unit properly. Reinsert the document. If misfeeding

occurs frequently, clean the document feeder rollers and try again. If the problem
remains, adjust the feeder pressure. (Refer to page 113.)

• Memory (telephone numbers, parameters, etc.) has been erased. Re-program.

[The backup battery on the top of the digital board may be low or dead, so check it.]

• The

to clear the message.

recording paper is not installed or the unit ran out of paper. Install paper and press

• The recording paper is not fed into the unit properly or has jammed near the recording

paper
the message.

entrance. Clear the jammed paper

Do not install folded or heavily curled paper in the paper tray.

• The unit has (a) document(s) in memory. See the other message instructions to print

out the document(s).

• The film is empty. Replace the film or film cartridge with a new one.
• The film is slack. Tighten it and install again.

• The remaining film can print about 15 pages of letter size documents. Prepare a new

film cartridge.

• Memory is full of received documents due to lack of recording paper or a recording

paper jam, etc. Install paper or clear the jammed paper.

• When performing memory transmission, the document being stored exceeds the

memory capacity of the unit. Transmit the entire document by using manual or automatic
transmission.

• The other party's fax machine is busy or ran out of recording paper. Try again.

• A recording paper jam occurred under the film cartridge. Clear the jammed paper.

[If the printout jams, please refer to 2.2.1. PAPER JAM.]

CHECK COVER

CHECK DOCUMENT

CHECK MEMORY

• The film cartridge is not inserted property. Reinsert it correctly.

CHECK FILM

CHECK PAPER

FAX IN MEMORY

FILM EMPTY

FILM NEAR EMPTY

• The free starter film is empty. Replace the film cartridge with a new one.

FREE FILM EMPTY

EASY DIAL FULL

• When making copy, the document being stored exceeds the memory capacity of the unit.

Press STOP to clear the message.

MEMORY FULL

FAX MEMORY FULL

NO FAX REPLY

PAPER JAMMED

MODEM ERROR

START/SET/COPY

and press to clear

START/SET/COPY

Note:

The explanations given in the [ ] are for servicemen only.

A translated version for each market is available with this model serise.

KX-FP101AL

Содержание KX-FP101AL















































































































































































































Результаты поиска

Содержание KX-FP101AL

Отзывы:

Похожие инструкции для KX-FP101AL

Бренды по названию

Популярные бренды

Panasonic KX-FP101AL, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP101AL

Отзывы:

Похожие инструкции для KX-FP101AL

Бренды по названию

Популярные бренды