Code
Function
Set Value Effective
Range
Default
Remarks
598
Receiving sensitivity
43= -43
dBm
20~48
40
Used when there is an error
Refer to
THE UNIT CAN COPY,
CANNOT EITHER TRANSMIT
RECEIVE LONG DISTANCE
INTERNATIONL COMMUNICATIONS
().
700
EXT.TAM OGM Rec. time
X second
01~99
10
Sets the start time of silent detection.
701
No voice detect time
X100 msec
01~99
50
Sets the silent call confirmation
detection time.
717
Transmit speed selection
1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4
1
Adjusts the speed to start training
during FAX transmission. Refer
SOMETIME THERE IS A TRANSMIT
PROBLEM
() and
THE UNIT CAN
COPY, BUT THE TRANSMISSION
AND RECEPTION IMAGE ARE
INCORRECT
().
718
Receive speed selection
1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4
1
Adjusts the speed to start training
during FAX reception. Refer
RECEIVE PROBLEM
() and
THE
CAN COPY, BUT THE
TRANSMISSION AND RECEPTION
IMAGE ARE INCORRECT
().
722
Redial tone detect
1:ON 2:
OFF
1, 2
2
Sets the tone detection mode
redialing.
745
Power ON film feed
1:ON 2:
OFF
1, 2
1
When the power is turned on,
film is wound to take up any
763
CNG detect time for
friendly reception
1:10 sec
2:20 sec
3:30 sec
1~3
3
Selects the CNG detection tone
friendly reception.
771
T1 timer
1:35 sec
2:60 sec
1, 2
1
Sets a higher value when the
response from the other party
more time during FAX transmission.
774
T4 timer
X 100
msec
00~99
0
Use this function when delay
in the line and communication
Mobile comm) does not work
815
Sensor & Vox check
See
TEST FUNCTIONS
().
69
Содержание KX-FHD332C
