Panasonic KV-S1020C SERIES страница 71 Скачать руководство пользователя

Страница: 71 / 117

9.3.7.

Adjust

Item

Operation

Default

Remarks

Shading

1. Click

“Shading”

on the main menu to execute shading

   correction.
2. Clean the conveyor, rollers, and scanning area (glass,
   reference area) according to the message on the display.
    And click

“OK”

3. Set the Shading Sheet (Part No.: See 14.3.) on the Feed
Tray in the

portrait

orientation.

And click

“OK”

to start the shading correction.

4. Confirm the result.
5. Click

“OK”

to get back to the main menu.

—

All Position

1. Set 2 pcs of Test Chart A4 (Part No.: See 14.3.) on the Feed
Tray in the

portrait

orientation.

2. Click

“All Position”

on the main menu to execute the

scanning position, length, width, and paper-end adjustment.
3. Check the result.
4. Click

“OK”

to get back to the main menu.

—

Set 2 pcs of Test Chart A4 in
the following order.
1

page: Position the chart

faced down.
2

page (KV-S1025C Series

Only): Position the chart
faced up.

Содержание KV-S1020C SERIES






















































































































Результаты поиска

Содержание KV-S1020C SERIES

Отзывы:

Похожие инструкции для KV-S1020C SERIES

Бренды по названию

Популярные бренды

Panasonic KV-S1020C SERIES, Руководство по обслуживанию

Результаты поиска

Содержание KV-S1020C SERIES

Отзывы:

Похожие инструкции для KV-S1020C SERIES

Бренды по названию

Популярные бренды