Panasonic GP6DU Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 127

background image

Power-on Operation

Power-on Operation (TH-42PD25U)

TH-42PD25U-P Standby Circuit.

Refer to figure 24. When the unit is plugged into the AC line, the PF-board provides
filtered AC voltage to the P-board through the connector P9. The AC is applied to a
standby circuit (D404, T410 and IC409) where the standby 7V is generated. This
voltage is applied to the 5V regulator circuit (Q552 and Q537) to generate the standby
5V.

The standby 5V is applied to the microprocessors on the D-board (IC9701 and IC9709).
This voltage is also routed through the PA-board to the microprocessor on the DG
board (IC001). This 5V is also applied to the EEPROM and the remote receiver sensor.

TH-42PD25U-P Power-On with Switch on the Front Panel

Refer to figure 23. When the unit is connected to the AC, the “Standby” powers-up the
microprocessor IC001. As soon as the “Reset” operation of IC001 is complete, its pin
48 goes “High”. The “High” from pin 48 is routed through pins 36 of connector DG2/PA2
and pin 9 of connector PA10/PF10 to the base of the transistor Q990 on the PF-board,
turning it on. This turns on the relay RL901.

Via the relay, AC is applied to the bridge rectifier D920. The DC control circuit (IC 920
and T920) regulates the resulting DC and provides two voltage sources, one is 10V and
the other is 24V. Both sources are routed to the PA-Board. The 10V source is routed
via pins 1 and 2 of the connector PF10/PA10, and the 24V is routed via pin 5 of the
same connector.

Using DC-DC converters, many secondary DC sources are derived from the 10V and
24V sources, on the PA-Board. These secondary sources Main 9V, Main 2.5V, Main
5V, Sub 5V, BT 30V, and VD1 (5V) are all commanded by one on/off line. A “High”
from pin 53 of IC001 turns on all the secondary sources when the TV is turned on by
either the on/off switch on the set or remote control.

Power Detect is accomplished by applying the Main 5V via pins 11 and 13 of
connectorPA2/DG2 to Q030, which applies a “Low “ to pin 52 of IC001.

The on/off switch on the front panel is a momentary switch, located on the K-Board, that
grounds pin 67 of IC001 when pressed.

In addition, the “High” from pin 53 is used to communicate “Power Status” to the
microprocessor IC9709 on the D-Board via pin 5 of connector DG3 and pin 15 of
connector D3.

29

«
...
33
34
35
36
37
...
»

Содержание GP6DU
































































































































Отзывы:

Нет отзывов

Похожие инструкции для GP6DU

Z50PX2D - 50" Plasma HDTV

Бренд: Zenith Страницы: 2

Бренд: XOCECO Страницы: 34

Бренд: Samsung Страницы: 38

Бренд: Philips Страницы: 34

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 136

Бренд: Philips Страницы: 3

Бренд: Samsung Страницы: 154

Бренд: Samsung Страницы: 103

Бренд: Panasonic Страницы: 52

Бренд: Proview Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды