Panasonic GM1 Series Скачать руководство пользователя страница 34

Страница: 34 / 98

Setting item

Default

Description

UpperLimitComparisonONLevel 1000

Specify the upper limit comparison ON level.
-32768 to +32767

UpperLimitComparisonOFFLev
el

1000

Specify the upper limit comparison OFF level.
-32768 to +32767

LowerLimitComparisonONLevel 0

Specify the lower limit comparison ON level.
-32768 to +32767

LowerLimitComparisonOFFLev
el

Specify the lower limit comparison OFF level.
-32768 to +32767

MaxMinValueRetention

Not execute

Select "Not execute / Execute" for the Max. / Min. hold.

DisconnectionDetection

Not execute

Select "Not execute / Execute" for the disconnection
detection.

DisconnectionDetectionReset

Automatic reset

Select reset operation when disconnection detection is
executed.
Automatic reset / Manual reset

4.3.2 List of Analog_8IN I/O Mapping

This section explains operations of channels used by the GM1 Analog Input Unit.

■

InputArea (input area)

● The asterisk ”*” represents the channel number. (0 to 7)

Channel

Type

Description

Operation

Ch*_InputValue

INT

Ch*_Analog Input
Value

Stores a digital value equivalent to the analog
input signal.
Stores a value before "Offset / Gain
processing" and "scale conversion" are
executed.

Ch*_ ConversionValue

INT

Ch*_Analog
Conversion Value

Stores a digital conversion value equivalent to
the analog input signal.
Stores a value after "Offset / Gain processing"
and "scale conversion" are executed.

Ch*_MaxHoldingValue

INT

Ch*_Max Holding
Value

Holds the maximum value of the digital
conversion value while the Max. / Min. hold is
executed.

Ch*_MinHoldingValue

INT

Ch*_Min Holding
Value

Holds the minimum value of the digital
conversion value while the Max. / Min. hold is
executed.

Ch*_StatusRegister

WORD

Ch*_Status Register

Sets the following statuses in bulk in units of
WORD.

Ch*_
DisconnectionDetectio
n Status

BOOL

Ch*_Disconnection
Detection Status

When disconnection is detected: ON, when
disconnection is restored: OFF
Enabled only when 1-5 V, 4-20 mA range is
selected.

4.3 Setting the Analog Input Unit

4-8

WUME-GM1AIO-01

Содержание GM1 Series



































































































Результаты поиска

Содержание GM1 Series

Отзывы:

Похожие инструкции для GM1 Series

Бренды по названию

Популярные бренды

Panasonic GM1 Series, Справочное руководство

Результаты поиска

Содержание GM1 Series

Отзывы:

Похожие инструкции для GM1 Series

Бренды по названию

Популярные бренды