Panasonic GM1 Series Скачать руководство пользователя страница 10

Страница: 10 / 98

1.1 Safety Precautions

This section explains important rules that must be observed to prevent personal injury and

property damage.

● Injuries and damages that may occur as a result of incorrect use are classified into the

following levels and safety precautions are explained according to the level.

Indicates that there is a risk of death or serious injury

Indicates that there is a risk of minor injury or property damage

Indicates an action that is prohibited

Indicates an action that must be taken

● Take safety measures outside this product to ensure the safety of the entire system even

if this product fails or an error occurs due to external factors.

● Do not use this product in atmospheres that contain flammable gases.

Doing so may result in explosion.

● Do not throw this product into the fire.

Doing so may cause the batteries or other electronic parts to explode.

● To prevent abnormal heat generation or smoke generation, use this product with some

leeway from the guaranteed characteristics and performance values of the product.

● Do not disassemble or modify this product.

Doing so may result in abnormal heat generation or smoke generation.

● Do not touch any terminals while the power is on.

Doing so may result in electrical shock.

● Configure emergency stop and interlock circuits outside this product.

● Connect wires and connectors properly.

Failure to do so may result in abnormal heat generation or smoke generation.

● Do not perform work (such as connection or removal) with the power turned on.

Doing so may result in electrical shock.

● If this product is used in any way that is not specified by Panasonic, its protection function

may be impaired.

● This product has been developed and manufactured for industrial use only.

1.1 Safety Precautions

1-2

WUME-GM1AIO-01

Содержание GM1 Series



































































































Результаты поиска

Содержание GM1 Series

Отзывы:

Похожие инструкции для GM1 Series

Бренды по названию

Популярные бренды

Panasonic GM1 Series, Справочное руководство

Результаты поиска

Содержание GM1 Series

Отзывы:

Похожие инструкции для GM1 Series

Бренды по названию

Популярные бренды