INSTRUCTION MANUAL
Digital Fiber Sensor Amplifier
FX-501
□
MJE-FX501C No.0052-92V
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
●
Never use this product as a sensing device for personnel protection.
●
In case of using sensing devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel
protection applicable in each region or country.
1
INTENDED PRODUCTS FOR CE MARKING
●
This product complies with the following standards / regulations.
<EU Directive>
EMC Directive
<Standards in US / Canada>
ANSI/UL 60947-5-2, CAN/CSA C22.2 No.14
<Regulations in Korea>
S1-G-1-2009, S2-W-5-2009
●
Caution about UL recognition
In case requiring conformity of UL listing mark or C-UL listing mark, USe class
2 power supply unit.
●
Contact for CE
Panasonic Marketing Europe GmbH Panasonic Testing Center
Winsbergring 15, 22525 Hamburg,Germany
2
PART DESCRIPTION
MODE indicator: PRO (Yellow)
MODE indicator: L / D (Yellow)
Digital display
(Green / Red)
UP key
•
Teaching
•
Threshold value
fine adjustment
•
Select setting items
SET key
•
Teaching
•
Confirm setting
contents
DOWN key
•
Teaching
• Threshold value fine
adjustment
•
Select setting items
Sensing output
operation indicator
(Orange)
MODE key
•
Select Modes
•
Cancel during setting
MODE indicator: CUST (Yellow)
Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock
3
MOUNTING
How to connect
1.
Fit the rear part of the mounting sec-
tion of the amplifier on a DIN rail.
2.
Press down the rear part of the
mounting section of the unit on the
DIN rail and fit the front part of the
mounting section to the DIN rail.
How to remove
1.
Push the controller forward.
2.
Lift up the front part of the amplifier
to remove it.
2.
Lift up
1.
Push forward
2.
Press down
1.
Fit
35mm width DIN rail
How to connect the fiber cable
Be sure to fit the attachment to the fibers first before inserting the fibers to the
amplifier. For details, refer to the instruction manual enclosed with the fibers.
1.
Snap the fiber lock lever down till it
stops completely.
2.
Insert the fiber cables slowly into the
inlets until they stops. (Note)
3.
Return the fiber lock lever to the
original position till it stops.
Fiber lock lever
Fiber for
receiver
1.
Snap
3.
Return
2.
Insert
Fiber for emitter
Note: With the coaxial reflective type fiber, such as ,
FD-G4
or
FD-FM2
, insert the single core fiber cable into the
beam-emitting inlet “P” and the multi-core fiber cable into the beam-receiving inlet.
If they are inserted in reverse, the sensing performance will deteriorate.
<Reference>
4
INSTALL MORE AMPLIFIER OF SERIES CONNECTION TYPE
●
Make sure that the power supply is OFF while adding or removing the series
connection type.
●
In case 2 or more the series connection types are connected in cascade,
make sure to mount them on a DIN rail.
● In case installing additional amplifier of series connection type, the maximum
11 the series connection types using sub cables can be added to an amplifier
using a main connection cable.
●
When connecting 2 or more the series connection types in cascade, use the
sub cable (optional) for the second series connection type onwards.
For mounting and removing the amplifier, refer to “
MOUNTING
.”
How to cascade
1.
Mount the amplifiers, one by one,
on the DIN rail.
2.
Slide the amplifiers next to each
other, and connect the quick-
connection cables.
3.
Mount the end plates
MS-DIN-E
(optional) at both the ends to hold
the amplifiers between their flat
sides.
4.
Tighten the screws to fix the end
plates.
How to Remove
1.
Loosen the screws of the end
plates.
2.
Remove the end plates.
3.
Slide the amplifiers and remove
them one by one.
Slide
Communication
window
Slide
Main cable
(Optional)
Sub cable
(Optional)
End plate
MS-DIN-E
(Optional)
End plate
MS-DIN-E
(Optional)
5
I/O CIRCUIT DIAGRAMS
<FX-501>
+
-
12 to 24V DC
%
Main circuit
(Brown) +V (Note)
(Black) Sensing output
(Blue) 0V (Note)
Load
<FX-501P>
Main circuit
(Brown) +V (Note)
(Black) Sensing output
(Blue) 0V (Note)
Load
+
-
12 to 24V DC
%
Note: The quick-connection sub cable does not incorV (brown) and 0V (blue). The power is supplied from
the connector of the main cable.
<Terminal arrangement>
2
3
1
Terminal No.
Terminal name
1
+V
2
Sensing output
3
0V
6
OPERATION PROCEDURE
The changed settings are not stored if turning the power OFF while
setting. Therefore, confirm the settings by pressing the SET key before
turning the power OFF.
●
When turning ON the power, RUN mode is displayed and the digital display
shows the threshold value (green) and the incident light intensity (red).
•
Displays threshold value (green) and incident light intensity (red).
• Teaching, threshold value fine adjustment and key lock function
can be set.
•
For setting method of each function, refer to “
TEACHING
MODE
,” “
THRESHOLD VALUE FINE ADJUSTMENT FUNC-
TION
,” or “
KEY LOCK FUNCTION
.”
<RUN mode>
•
Select either Light-ON or Dark-ON.
•
For the setting, refer to “
SENSING OUTPUT OPERATION
MODE
.”
•
The default setting is “
” (Light-ON).
<Sensing output operation mode>
•
An item set in CUSTOM mode (Response time setting, Emission
power setting and Hysteresis setting) is displayed.
•
For details, refer to “
CUSTOM MODE
.”
•
The default setting is “
” (response time setting).
<CUSTOM mode>
•
Advanced setting can be done.
•
For the setting, refer to “
PRO MODE
.”
<PRO mode>
<RUN mode>
