Panasonic FA-DS72 Скачать руководство пользователя страница 130

Страница: 130 / 402

5-53

Troubleshooting

E3-50: Transfer cleaner operation

When the transfer cleaner motor drives, the transfer cleaner home position sensor

is not ON/OFF within a predetermined time.

Is the wire cleaner felt

Does the wire cleaner felt connect to

at the home position sensor?

the corona rail slider?

YES

a) Turn the transport lever and lower the

transport unit

b) Press down the transfer charger and draw it

toward you.

c) Slide the wire cleaner felt to rear side until it

stops.

d) Re-install the transfer charger.

e) Turn the transport lever and raise the

transport unit.

f) Check the wire cleaner felt is connected to

the corona rail slider.

YES

Check operation

Is DC5V detected on sensor CN-1?

Sensor connector is shorted or broken.

YES

Does CN4-5 (output signal of control

Sensor is defective

panel CPU PCB) change when the

sensor is turned ON/OFF?

E4-01: Fuser warm-up

When the fuser temperature does not reach the predetermined level

within a predetermined time.

Does fuser lamp turned ON after

YES

Fuser thermistor is dirty.

the power switch is turned on?

Sensor position is incorrect.

Fuser temperature is low (re-adjust F6-31)

Fuser thermistor is defective.

Is these continuity between

Fuser lamp connector is shorted or broken.

CN-1 and 2 when the

Fuser thermostat is defective.

AC driver PCB CN203 is removed.

Fuser lamp is defective.

YES

Is there some registrance between

CNTH connector is shorted or broken.

CNTH-1 and 2 approximately few M ,

Fuser thermistor is defective.

whenCPU PCB CN7 is removed.

(approx. 1.4M /77F, 25°C)

Содержание FA-DS72



















































































































































































































































































































































































































Результаты поиска

Содержание FA-DS72

Отзывы:

Похожие инструкции для FA-DS72

Бренды по названию

Популярные бренды

Panasonic FA-DS72, Руководство по обслуживанию и каталог запасных частей

Результаты поиска

Содержание FA-DS72

Отзывы:

Похожие инструкции для FA-DS72

Бренды по названию

Популярные бренды