background image

- 12 - 

Li-ion Battery Pack

NOTE:

Your battery pack is not fully charged 

at the time of purchase. Be sure to 

charge the battery before use.

Battery charger

1.  Plug the charger into the AC outlet.

2.  Insert the battery pack firmly into the 

charger.

1. Line up the alignment marks and 

place the battery onto the dock on the 

charger.

2. Slide forward in the direction of the 

arrow.

Alignment marks

3.  During charging, the charging lamp 

will be lit.

When charging is completed, an 

internal electronic switch will 

automatically be triggered to prevent 

overcharging.

•  Charging will not start if the 

battery pack is warm (for example, 

immediately after heavy-duty 

operation).

The orange standby lamp will be 

flashing until the battery cools down.

Charging will then begin automatically.

4.  The charge lamp (green) will 

flash slowly once the battery is 

approximately 80% charged.

5.  When charging is completed, the 

charging lamp in green color will turn 

off.

6.  If the temperature of the battery pack 

is 0°C or less, charging takes longer 

to fully charge the battery pack than 

the standard charging time.

  Even when the battery is fully 

charged, it will have approximately 

50% of the power of a fully charged 

battery at normal operating 

temperature.

7.  Consult an authorized dealer if the 

charging lamp (green) does not turn 

off.

8.  If a fully charged battery pack is 

inserted into the charger again, the 

charging lamp lights up. After several 

minutes, the charging lamp in green 

color will turn off.

9.  Remove the battery pack while the 

battery pack release button is held 

up.

Battery pack 

release button

LAMP INDICATIONS

Charging is completed. (Full charge.)

Battery is approximately 80% charged. 

Now charging.

Charger is plugged into the AC outlet. Ready to charge.

(Green)

(Orange)

Charging Status Lamp.

Left: green  Right: orange will be displayed.

Battery pack is cool.

The battery pack is being charged slowly to reduce the load on the battery. 
Battery pack is warm. 

Charging will begin when temperature of battery pack drops. If the temperature of the 

battery pack is -10° or less, the charging status lamp (orange) will also start flashing.

Charging will begin when the temperature of the battery pack goes up"
Charging is not possible. Clogged with dust or malfunction of the bat-

tery pack.

   Turn off 

   Lit 

   Flashing

EY7442_7450_7950(UL).indb   12

2011-2-17   11:48:05

Содержание EY7950LR2S















Отзывы: