9
formance.
With the system outer foil in place,
apply some hand soap onto the outer
foil. Push the On/Off switch more
than 2 seconds to activate the turbo
mode for “sonic” vibration cleaning.
At the same time, the lamps of the
Battery capacity monitor/Charge sta-
tus lamp will flash around randomly.
Pour some water over the outer foil.
After about 20 seconds, it will be
automatically turned off, or you can
turn it off by pushing the On/Off
switch.
Remove the system outer foil and
clean it with running water. Wipe off
any moisture from the shaver with a
dry cloth and remove the protective
cap to allow the system outer foil to
dry completely.
Replacing shaving head
components
It is recommended that you replace
the system outer foil at least every
year and the inner blade at least
every 2 years to maintain your shav-
er’s cutting performance.
Replacing the system outer
foil
(see fig. 8)
Squeeze the system outer foil re-
lease buttons and lift the system
outer foil upward to remove it. To in-
sert the new system outer foil, press
it down until it snaps into place.
Replacing the inner blades
(see fig. 9)
Squeeze the system outer foil re-
lease buttons and lift the system
outer foil upward to remove it. Re-
move the inner blade one at a time
by grasping it firmly at both ends and
pulling straight away from the shaver.
Do not touch the metal parts of inner
blades.
To insert the new inner blade, hold
the blade one at a time at both ends
and press downward until it snaps
into the shaver.
ATTENTION:
A nickel metal hydride battery that
is recyclable powers the product
you have purchased. Please call
1-800-8-BATTERY for information
on how to recycle this battery.
How to remove the built-in
rechargeable batteries before
disposal of the shaver
(see fig. 10)
The batteries in this shaver are not
intended to be replaced by consum-
ers. However, the batteries may be
replaced at an authorized service
center. The procedure described be-
low is intended only for removal of
the rechargeable batteries for the
purpose of proper disposal.
1. Slide the trimmer handle up until
it clicks in.
8
utes per shave for a normal beard).
You can always store your shaver in
the charging adaptor to maintain full
battery capacity. This shaver cannot
be overcharged.
Before traveling, charge it fully for 1
hour if you will not be taking the
charging adaptor with you.
In case your shaver is without
charge, you may quick charge it for
1 shave in about 5 minutes.
Using your shaver
Push the On/Off switch to turn the
shaver on.
If you push and hold the On/Off
switch for more than 2 seconds, it
will activate the turbo mode for
“sonic” vibration cleaning.
(see “Cleaning your shaver”)
Caution:
Shaving with “sonic” vibration may
damage your skin. Please turn it
off and on again to deactivate the
turbo mode.
Hold the shaver at a right angle (90
°
)
to your skin (see fig. 3). Start out
shaving by applying gentle pressure
to your face. Stretch your skin with
your free hand and move the shaver
back and forth in the direction of your
beard. You may gently increase the
amount of pressure as your skin be-
comes accustomed to this shaver.
Applying excessive pressure does
not provide a closer shave.
Pivot action selector
(see fig. 4)
Use the pivot action selector to
choose the shaving mode.
soft, •, lock based on your shaving
preference.
The pivot action can be changed no
matter whether the switch is turned
on or off.
For wet shaving
Put a thin layer of shaving foam on
your face which works as a lubrica-
tor. Shaving foam is the most suit-
able among many other shaving aids
(gel, soap, cream, etc). Do not put a
thick layer of shaving foam as it may
affect shaver’s performance. If the
shaving head is clogged with foam,
simply rinse it under running water.
System outer foil
(see fig. 5)
System outer foil has a slit blade (a)
between 2 foils (b). They move up
and down independently to follow the
contours of your face.
The slit blade catches and cuts
longer and lying hairs easily.
Using the trimmer
(see fig. 6)
Slide the trimmer handle up until it
clicks in. Place the trimmer at a right
angle to your skin and move it down-
ward to trim sideburns.
Cleaning your shaver
(see fig. 7)
For cleanliness and convenience, we
recommend that you clean your
shaver with water and a liquid hand
soap. Regular cleaning will keep your
shaver in good condition while pre-
venting odors or bacteria from devel-
oping, and maintain the cutting per-
9
8
P07-11̲ES8092(USA) 03.6.11 19:37 ページ8
