Panasonic EP3203-U1 Скачать руководство пользователя

Страница: 85 / 114

10.13.6. Removing the Air unit

1. Disconnect Connectors (CN201, CN208) of the Main PCB.

2. Unscrew five screws of the Main PCB installation plate and four screws of the Air

unit.

3. Cut off the Insulated tie medium of the Air hoses.

Caution when installing

- You can remove the Air unit with the five screws loose of the Main PCB

installation plate.

10.13.7. Removing the Width motor

1. Disconnect Connectors (CN102, CN500) of the Main PCB.

2. Cut off one Insulated tie medium, and two small.

3. Remove the Width belt.

4. Unscrew four screws of the Width motor.

10.13.8. Removing the Back vibrator

1. Disconnect Connectors (CN2102, CN211) of the Main PCB.

2. Cut off three Insulated ties medium of the Lead wires.

3. Unscrew two screws of the Back vibrator.

Caution when removing

Содержание EP3203-U1



















































































































Результаты поиска

Содержание EP3203-U1

Отзывы:

Похожие инструкции для EP3203-U1

Бренды по названию

Популярные бренды

Panasonic EP3203-U1, Руководство по обслуживанию

Результаты поиска

Содержание EP3203-U1

Отзывы:

Похожие инструкции для EP3203-U1

Бренды по названию

Популярные бренды