Panasonic EASA-PHONE KX-T123220 Скачать руководство пользователя страница 206

Страница: 206 / 242

PROBLEM

Extension does not operate.

When using the
speakerphone mode,
nothing is heard.

The unit does not ring.

During a power
interruption,

extensions connected to
jack number

10, 17

and 18 do not operate.

PROBABLE CAUSE

The Power failure switch of
the KX-Tl23230,

KX-T61630 or

KX-T30830 is set to ON.

The HANDSET/HEADSET

selector of the KX-Tl23230,

KX-T61631, KX-T61630 or
KX-T30830 is set to the
“HEADSET” position.

Ringer Volume Selector is

set to “OFF”.

The CO numbers are not

programmed.

Power failure switch

of the KX-Tl23230,

KX-T61630 or

KX-T30830 is set to OFF.

The dialing mode (tone or

pulse) is improper.

KX-T61620, KX-T616.50,
KX-T30820 or KX-T30850

is connected.

If the system is not operating properly, use the Reset
Button.

Before using the Reset Button, try the system

feature again which does not work several times

to confirm there definitely is a problem.

Pressing the Reset button will cause the

followings.

1. Camp-on to be cleared.

2. Last number redial to be cleared.
3. Saved number redial to be cleared.
4. Calls on hold are terminated.

5. Calls on exclusive hold are terminated.
6. Calls in progress are terminated.

7. Call park to be cleared.
8. Message Waiting to be cleared.

Data that are stored in memory other than above
mentioned will not be cleared by use of the Reset
Button.

POSSIBLE SOLUTION

Set the Power failure switch to OFF.

When the headset is not used, set the HANDSET/

HEADSET selector to the “HANDSET” position.

to “HIGH” or “LOW”.

See “CO Line Ringing Selection” on page 4-58.

Set the Power failure switch to ON.

Set the Tone/Pulse switch to the other position.

Disconnect KX-Tl23220, KX-Tl23250,

KX-T61620, KX-T61650, KX-T30820 or
KX-T30850 and connect the KX-T123230,
KX-T61631, KX-T61630, KX-T30830 or a

standard telephone.

Note

If the system does not operate properly, push the
Reset Button.
If there still is no difference, switch the power off

and on again after 5 minutes. If the system still does
not work, switch the power off.
The following extensions will be directly connected
to each of the central office lines (C.O.).

Extension connected to jack number01 . . . CO 1
Extension connected to jack number02 . . . . CO 2
Extension connected to jack number09 . . . . . . CO

Extension connected to jack number10 . . . . . . CO

Extension connected to jack number17 . . CO 9
Extension connected to jack number18 . . . . . . CO1 0

If the automobile type battery is connected to the

system, disconnect it.

6-3

Содержание EASA-PHONE KX-T123220



















































































































































































































































Результаты поиска

Содержание EASA-PHONE KX-T123220

Отзывы:

Похожие инструкции для EASA-PHONE KX-T123220

Бренды по названию

Популярные бренды

Panasonic EASA-PHONE KX-T123220, Руководство по установке

Результаты поиска

Содержание EASA-PHONE KX-T123220

Отзывы:

Похожие инструкции для EASA-PHONE KX-T123220

Бренды по названию

Популярные бренды